LiftMaster MAXUM Commercial Door Operators Instruction Manual
Documentation Information
- Manufacturer
- LiftMaster
- Models
- MAXUM industrial DC operators: JDC and RJDC (jackshaft), JHDC (hoist), and TDC (trolley)
- Equipment type
- Commercial door operators (not for residential use) for sectional and rolling doors up to 700, 1,200, and 2,200 lbs, with LCD wall control, myQ Wi-Fi, and optional battery backup
- Document type
- Installation Manual (English, French, and Spanish in one PDF; this page presents the English version, pages 1 to 92)
- Manufacturer document number
- 114-6042-000
- Manual revision
- Rev. I
- Manual copyright / publication
- ©2026 The Chamberlain Group LLC. The manual does not print a revision date.
- Source
- LiftMaster MAXUM Installation Manual; see Original LiftMaster Documentation
- HTML resource last updated
- November 19, 2026
Common tasks: Choose an operator | Decode a model number | Pick a door sprocket | Install a trolley | Install a jackshaft or hoist | Commission | Error codes | Parts
LiftMaster MAXUM Commercial Door Operators Overview
LiftMaster's Installation Manual 114-6042-000 (Rev. I) covers the MAXUM industrial DC operators: models JDC, RJDC, JHDC, and TDC, described on the cover as DC jackshaft, hoist, and trolley operators for doors up to 700, 1,200, and 2,200 lbs. The cover marks them NOT FOR RESIDENTIAL USE and says the product is to be installed and serviced by a trained door systems technician ONLY. The operators are compatible with myQ, myQ Facility, and Security+ 2.0 accessories, are Wi-Fi compatible, and are Bluetooth enabled (firmware v2.0 and newer).
Which MAXUM Operator Do You Have?
The manual groups the MAXUM line into three families by how the operator drives the door. The model decoder is in Model Decoder.
Swipe sideways to see all columns.
| Family | Manual models | How it drives the door | Door weight in the manual | ASE product page |
|---|---|---|---|---|
| Jackshaft | JDC (no hoist, no release, battery backup included on the 700 model); RJDC (jackshaft with manual release sash chain) | Mounts on a wall, shelf, or bracket and drives the door shaft through a chain and door sprocket | Up to 700 lbs | MAXUM jackshaft commercial door operator |
| Hoist | JHDC (jackshaft with hoist; hand chain and engage/disengage ropes) | Same chain drive as the jackshaft, plus a manual hoist chain for emergencies | Up to 700, 1,200, or 2,200 lbs | MAXUM hoist commercial door operator |
| Trolley | TDC (trolley; chain output) | Hangs from a header bracket and pulls a trolley along a track with a door arm | Up to 700, 1,200, or 2,200 lbs | MAXUM trolley commercial door operator |
All Security Equipment note. Our three MAXUM product pages are the jackshaft (700 lb, 120/240V or 480V), the hoist (700 lb and 1,200 lb standard and extended duty, 120/240V or 480V), and the trolley sold without rails (700 lb and 1,200 lb standard and extended duty, with several door height options). The manual also covers 2,200 lb JHDC and TDC models and the RJDC manual release model, which are not listed on those three product pages; call (800) 730-8382 for custom configurations. Each product page lists the included DCWALLCTL floor level wall controller with 4-line LCD display and CPS-U monitored through-beam photo eye kit, and free myQ Facility Access with every MAXUM operator.
What the Manual Covers
- Safety information and door sprocket selection (pages 3 to 5)
- Model decoder, electrical ratings, specifications, and dimensions (pages 6 to 14)
- Trolley (TDC) carton, assembly, and installation (pages 15 to 20)
- Jackshaft (JDC), release (RJDC), and hoist (JHDC) carton, assembly, installation, and manual release (pages 21 to 27)
- Wiring, wall controller, entrapment protection, cable tension monitors, and wiring diagrams (pages 28 to 38)
- Programming, operating modes, reset options, remotes, and Wi-Fi (pages 39 to 60)
- Troubleshooting and error codes (pages 61 to 83), maintenance (page 84), accessories and service parts (pages 85 to 91), and warranty (page 92)
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), cover and page 2.
Models and Specifications
Voltage Selection (Page 6)
Swipe sideways to see all columns.
| Supply voltage | How it is supplied |
|---|---|
| 120/240V single and 3 phase | Dedicated SKU |
| 480V 3 phase | Dedicated SKU |
| 208V 3 phase | Via accessory step down transformer |
| 600V 3 phase | Via accessory step down transformer |
Model Decoder (Page 6)
Model numbers are built from the type, door weight, duty cycle, voltage, battery backup, shaft, and handing codes below (examples: JDC7S1BMC, RJDC7S4BEL, JHDC12X1BMC, TDC22X4BMC).
Swipe sideways to see all columns.
| Code position | Options as printed |
|---|---|
| Type | J = jackshaft, no hoist, no release (JDC); RJ = jackshaft with release (RJDC); JH = jackshaft with hoist (JHDC); T = trolley (TDC). All are "DC" (DC operators). |
| Door weight | 7 = up to 700 lb doors; 12 = up to 1200 lb doors; 22 = up to 2200 lb doors (JHDC and TDC). JDC and RJDC are 7 only. |
| Duty cycle | S = standard; X = continuous duty (JHDC and TDC; "extended duty" for firmware versions 1.17 and prior). |
| Voltage | 1 = 120/240V single or 3 phase; 4 = 480V 3 phase. |
| Battery backup | B = includes battery backup unit (JDC), or battery backup capable, not included (RJDC, JHDC, TDC). |
| Extended shaft (jackshaft and hoist) | E = extended shaft; MC = no significance (dual handed). RJDC adds L (left-handed) or R (right-handed). |
| Handing | Dual handed (JDC and JHDC); L or R (RJDC); not applicable (TDC). |
Model Electrical Ratings (Pages 6 and 7)
Swipe sideways to see all columns.
| Model family | Cycle | Max door weight | Electrical rating (as printed) |
|---|---|---|---|
| RJDC7S1BEL, RJDC7S4BEL, RJDC7S1BER, RJDC7S4BER (jackshaft with manual release) | Standard | 700 lbs | 120Vac 5A 1PH; 240Vac 2.5A 1PH/3PH; 480Vac 1.25A 1PH/3PH (BBU capable) |
| JDC7S1BMC, JDC7S4BMC, JDC7S1BE, JDC7S4BE (jackshaft, non-hoisted) | Standard | 700 lbs | 120Vac 5A 1PH; 240Vac 2.5A 1PH/3PH; 480Vac 1.25A 1PH/3PH (BBU included) |
| JHDC7S1BMC, JHDC7S4BMC, JHDC7S1BE, JHDC7S4BE (hoist) | Standard | 700 lbs | 120Vac 5A 1PH; 240Vac 2.5A 1PH/3PH; 480Vac 1.25A 1PH/3PH |
| JHDC12S1BMC, JHDC12S4BMC, JHDC12S1BE, JHDC12S4BE (hoist) | Standard | 1200 lbs | See page 7 |
| JHDC12X1BMC, JHDC12X4BMC, JHDC12X1BE, JHDC12X4BE (hoist) | Continuous | 1200 lbs | See page 7 |
| JHDC22X1BMC, JHDC22X4BMC (hoist) | Continuous | 2200 lbs | See page 7 |
| TDC7S1BMC, TDC7S4BMC (trolley) | Standard | 700 lbs | 120Vac 5A 1PH; 240Vac 2.5A 1PH/3PH; 480Vac 1.25A 1PH/3PH |
| TDC12S1BMC, TDC12S4BMC (trolley) | Standard | 1200 lbs | See page 7 |
| TDC12X1BMC, TDC12X4BMC (trolley) | Continuous | 1200 lbs | See page 7 |
| TDC22X1BMC, TDC22X4BMC (trolley) | Continuous | 2200 lbs | See page 7 |
For the 1200 and 2200 families, the page 7 table prints these rating values: 120Vac 9A 1PH with 240Vac 4.5A 1PH/3PH; 120Vac 10A 1PH with 240Vac 5A 1PH/3PH; 480Vac 3A 1PH/3PH; and 480Vac 3.5A 1PH/3PH. Check the page 7 table in the original manual for which rating belongs to each model.
Notes from the manual: "BBU capable" models can accept a battery backup unit; "BBU included" models ship with it. "Extended duty" applies to firmware versions 1.17 and prior, or manufacture dates before February 9, 2026. "Continuous duty" applies to operators manufactured on or after February 9, 2026 with firmware version 1.21 or later. Refer to the NEMA 4X Manual Addendum for NEMA 4X models and ratings.
Operator Specifications (Page 8)
Swipe sideways to see all columns.
| Specification | Value as printed |
|---|---|
| Duty cycles | Standard ("S" models): 20 cycles per hour. Extended ("X" models): 30 cycles per hour (firmware 1.17 and prior). Continuous ("X" models): 100 cycles per hour (firmware 1.21 and newer). |
| Wall controller | NEMA 1 general purpose 3-button wall controller (open/close/stop) with LCD display and floor level commissioning through a user menu. |
| Operation modes | C2 (factory default), B2, B2/T, B2/TS, D1, E2, and FSTS. |
| Brake | Standard dynamic braking on 700, 1200, and 2200; 2200 series include an electromechanical holding brake. |
| Limit adjust | Electronic limits with floor level adjustability. |
| Door speed (JDC, RJDC, JHDC) | 12" per second for sectional doors; 8 to 9" per second for rolling steel doors. |
| Door speed (TDC) | 12" per second for sectional doors. |
| Mechanical drive reduction | JDC, RJDC, and JHDC: 65:1 gearbox with #50 chain output. TDC: 65:1 gearbox with #48 chain output on 700 units and #41 chain output on 1200 and 2200 units. |
| Disconnect | JDC: none (includes battery backup for operating the door during an AC power failure). RJDC: manual release sash chain. JHDC: engage (green) and disengage (red) ropes electronically disable the controls so the door can be moved with the hoist chain. TDC: quick disconnect door arm. |
| Battery backup (BBU) | 20 cycles (fully charged, within 48 hours of AC power failure). |
| Temperature | Without heater: -4 F (-20 C) to +149 F (65 C). With the optional heater kit: -40 F (-40 C) to +149 F (65 C). |
| Environment | Indoor use only. |
| Fine speed adjustment | Made through the wall controller menu; to slow the operator down, change the sprocket choice. |
Documentation note. The page 7 electrical table loses the row-to-rating pairing for the 1200 and 2200 families when read as text, so this page shows only the 700 lb ratings that the page 6 table pairs clearly and lists the other printed values without assigning them to models. The dimension drawings on pages 9 to 14 are figures with numbers that do not extract as text; see those pages in the original manual for the dimensions.
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), pages 6 to 9.
Important Safety Information
Safety Symbols and Entrapment Protection (Page 3)
LiftMaster says that BEFORE attempting to install, operate, or maintain the operator you must read and fully understand the manual and follow all safety instructions, and not to attempt repair or service unless you are an Authorized Service Technician. A commercial door operator should only be installed on a properly balanced door. Monitored photoelectric sensors and/or door edge sensors are required for any momentary contact to close modes of operation (see Entrapment Protection). The manual includes a California Proposition 65 warning (www.P65Warnings.ca.gov).
Installation Warnings (Page 3)
To reduce the risk of SEVERE INJURY or DEATH:
- READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.
- Install the operator ONLY on a properly balanced and lubricated door. An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH.
- ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing the operator.
- Disable ALL locks and remove ALL ropes connected to the door BEFORE installing the operator to avoid entanglement.
- Install the operator a minimum of 8 feet (2.44 m) from the floor.
- NEVER connect a door operator to a power source until instructed to do so.
- NEVER wear watches, rings or loose clothing while installing or servicing an operator. They could be caught in the door or operator mechanisms.
- Install a wall controller within sight of the door, out of reach of small children and at a minimum height of 5 feet (1.5 m) above floors, landings, steps, or any other adjacent walking surface, and away from ALL moving parts of the door.
- Install the wall controller far enough from the door to prevent the user from coming in contact with the door while operating the controls.
- Install the entrapment warning placard on the wall next to the wall controller in a prominent location, visible from the door.
- Place the manual release/safety reverse test label in plain view on the inside of the door.
- Upon completion of installation, test the entrapment protection device(s).
- This door operator is not intended to replace door locks. With enough force, a door without a door lock can be opened. LiftMaster always recommends the use of door locks to properly secure a door.
- SAVE THESE INSTRUCTIONS.
Important Safety Instructions for Operation (Page 8)
To reduce the risk of SEVERE INJURY or DEATH:
- READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.
- ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with door control push buttons or remote controls.
- ONLY activate a door when it can be seen clearly, it is properly adjusted and no obstructions exist in the path the door will travel.
- Personnel should keep away from a door in motion and ALWAYS keep a door in sight until completely closed. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR.
- NO ONE SHOULD GO UNDER A STOPPED OR PARTIALLY OPENED DOOR.
- If possible, use the manual release handle to disengage a door ONLY when a door is CLOSED. Weak or broken springs or an unbalanced door could result in an open door falling rapidly and/or unexpectedly causing SEVERE INJURY or DEATH.
- NEVER use the manual release handle unless the doorway is clear of persons and obstructions.
- After ANY adjustments are made, the entrapment protection device(s) MUST be tested. Failure to adjust the operator properly may cause SEVERE INJURY and DEATH.
- Entrapment protection device(s) MUST be tested every month. Failure to adjust the operator properly may cause SEVERE INJURY and DEATH.
- ALWAYS KEEP THE DOOR PROPERLY BALANCED. An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH. See the door manufacturer's owner's manual.
- ALL repairs to cables, spring assemblies and other hardware, ALL of which are under EXTREME tension, MUST be made by an Authorized Service Technician.
- ALWAYS disconnect electric power to the door operator BEFORE making ANY repairs or removing covers.
- NEVER try to loosen or remove an obstruction that has impeded the movement of the door. Both the obstruction and door are under EXTREME tension and loosening or removing an obstacle can cause SERIOUS PERSONAL INJURY.
- NEVER stand under a door that has been impeded by an obstruction. KEEP CLEAR. The door could move freely at any time and can cause SERIOUS PERSONAL INJURY.
- If the door should be obstructed or impeded in its movement, ALWAYS call an Authorized Trained Service Technician to clear that obstruction.
- SAVE THESE INSTRUCTIONS.
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), pages 3 and 8.
Door Sprockets (JDC, RJDC, and JHDC Only)
JDC, RJDC, and JHDC 700 and 1200 models come with a 12-tooth drive sprocket pre-installed; JHDC 2200 models come with a 10-tooth drive sprocket pre-installed. A 10-tooth sprocket kit (part 71-1550B10LGH) converts 12-tooth operators in the field; a smaller drive sprocket reduces door speed, or allows a smaller door sprocket at the same door speed. Door sprocket kits (with keyway and setscrew) are sold and shipped separately, and the manual says sprockets will no longer be included in the box. Check MAXUM's price list (accessory page) for available door sprocket kits. For rolling doors greater than 20 ft in height, contact LiftMaster sales representatives.
Example of Sprocket Reduction at the Same Door Speed (Page 4)
Swipe sideways to see all columns.
| Door type | 12-tooth drive sprocket (door sprocket) | 10-tooth drive sprocket (door sprocket) |
|---|---|---|
| Sectional | 42-tooth | 32-tooth |
| Rolling steel | 60-tooth | 50-tooth |
Rolling Door Sprockets with the 12-Tooth Operator Sprocket, 700 and 1200 (Page 4)
For uninsulated rolling doors and grilles up to 20 ft in height at 8 to 9 in./sec, and insulated rolling doors up to 20 ft in height at 8 to 9 in./sec.
Swipe sideways to see all columns.
| Door | Series | Door weight | Door sprocket tooth count |
|---|---|---|---|
| Uninsulated | 700 | Up to 450 lbs | 50 |
| Uninsulated | 700 | 450 to 700 lbs | See page 4 |
| Uninsulated | 1200 | 700 to 1200 lbs | 72 |
| Insulated | 700 | Up to 450 lbs | 60 |
| Insulated | 1200 | 450 to 900 lbs | 72 |
Rolling Door Sprockets with the 10-Tooth Operator Sprocket (Page 5)
Standard for JHDC 2200; available as accessory kit 71-1550B10LGH for 700 and 1200, at 8 to 9 in./s.
Swipe sideways to see all columns.
| Door | Series | Door weight | Door sprocket tooth count |
|---|---|---|---|
| Uninsulated | 700 | Up to 450 lbs | 42 |
| Uninsulated | 700 / 1200 | 450 to 700 lbs / 700 to 1200 lbs | See page 5 |
| Uninsulated | 2200 | 1200 to 1800 lbs; 1800 to 2200 lbs | See page 5 |
| Insulated | 700 | Up to 450 lbs | 50 |
| Insulated | 1200 | 450 to 900 lbs | 60 |
| Insulated | 2200 | 900 to 2200 lbs | 72 |
Sectional Door Sprocket Recommendations (Page 4)
For 12-tooth (700/1200) and 10-tooth (2200) operator sprockets, the manual lists the recommended door sprocket by drum diameter and desired speed; the 1 in. bore parts end in LGH and the 1.25 in. bore parts end in QGH (1/4 in. keyway on both).
Swipe sideways to see all columns.
| Drum diameter | For 10 to 12 in./sec: teeth and 1 in. bore part (1.25 in. bore) | For 9 to 10 in./sec: teeth and 1 in. bore part (1.25 in. bore) |
|---|---|---|
| 4" | 16 teeth: 71-1550B16LGH (71-1550B16QGH) | 24 teeth: 71-1550B24LGH (71-1550B24QGH) |
| 5.25" to 5.75" and 8.5" vertical lift | 24 teeth: 71-1550B24LGH (71-1550B24QGH) | 32 teeth: 71-1550B32LGH (71-1550B32QGH) |
| 6.375" to 11" | 32 teeth: 71-1550B32LGH (71-1550B32QGH) | 42 teeth: 71-1550B42LGH (71-1550B42QGH) |
| 13.5" | 42 teeth: 71-1550B42LGH (71-1550B42QGH) | 56 teeth: 71-1550B56LGH (71-1550B56QGH) |
If You Are Unsure of the Drum Diameter (Page 5)
For sectional doors, if unsure of the door drum diameter, choose the 32-tooth door sprocket.
Swipe sideways to see all columns.
| Operator series | Desired door speed | Teeth | 1 in. bore part | 1.25 in. bore part |
|---|---|---|---|---|
| 700 | 12"/sec | 22 | 71-1550B22LGH | 71-1550B22QGH |
| 700 | 9"/sec | 32 | 71-1550B32LGH | 71-1550B32QGH |
| 1200 | 12"/sec | 22 | 71-1550B22LGH | 71-1550B22QGH |
| 1200 | 9"/sec | 32 | 71-1550B32LGH | 71-1550B32QGH |
| 2200 | 10"-12"/sec | 32 | 71-1550B32LGH | 71-1550B32QGH |
Documentation note. The rolling door sprocket tables on pages 4 and 5 lose some of their row-to-weight pairings when the page is read as text (the weight bands and tooth counts are laid out in separate columns), so rows that say "See page" above should be checked against the original tables before ordering a sprocket kit.
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), pages 4 and 5.
Trolley (TDC) Operators: Assembly and Installation
To prevent possible SERIOUS INJURY or DEATH (page 15): DO NOT connect electric power until instructed to do so. If the door lock needs to remain functional, install an interlock switch. ALWAYS call an Authorized Service Technician if the door binds, sticks, or is out of balance (an unbalanced door may NOT reverse when required). NEVER try to loosen, move, or adjust doors, door springs, cable, pulleys, brackets, or their hardware, ALL of which are under EXTREME tension. Disable ALL locks and remove ALL ropes connected to the door BEFORE installing and operating the operator. Fasten the operator SECURELY to structural supports of the building. Concrete anchors MUST be used in installing ANY brackets.
Trolley Carton Inventory (Page 15)
The operator is packaged in one carton that contains the motor unit and the items below. If anything is missing, carefully check the packing material. Trolley tracks and the drive chain are ordered and shipped separately from the operator packaging.
- Operator assembly and hardware box (fasteners, trolley, track spacers, door arm assembly, front idler, header mounting bracket)
- Installation manual and warning placards
- Floor level wall controller with LCD display
- LiftMaster monitored entrapment protection, CPS-U photoelectric sensors
- Extra trolley drive chain for retrofit installations
Assemble the Operator (Page 16)
Swipe sideways to see all columns.
| Track length | Spacers provided |
|---|---|
| 8 to 14 foot | 2 |
| 16 to 20 foot | 3 |
| 22 to 24 foot | 4 |
Hardware (page 16): bolt 3/8"-16 x 3/4" (A); flange hex nut 3/8"-16 (B); take-up bolt 5/16" (C); lock washer 3/8" (D); hex nut 5/16", qty. 2 (E); bolt 3/8"-16 x 1" (F); lock washer 5/16" (G).
- Install the track spacers evenly over the length of the track. Fasten the spacers to the track with bolt (A) and flange hex nuts (B).
- Install the front idler to the track with bolts (F) and washers (D).
- Assemble the trolley with the take-up bolt, 2 hex nuts, and lock washer: put the first hex nut (E) on the take-up bolt (C), push the take-up bolt through the trolley block, and secure with the lock washer (G) and the second hex nut (E).
- Slide the trolley onto the track.
- Insert bolts (A) into the end of the track and loosely thread the nuts (B) onto the ends of the bolts.
- Slide bolts (A) on the end of the track assembly into the "L" slot in the operator and tighten nuts (B). Insert bolts (A) into the holes on the end of the track and the operator. Secure the track with nuts (B).
Install the Chain (Page 17)
The chain is packed separately from the operator; make sure you have your chain before starting installation.
- Position the trolley 2 inches (5.1 cm) away from the front idler.
- Attach the chain to the trolley threaded shaft using the master link.
- Run the chain along the track to the operator. Wrap the chain around the operator drive sprocket.
- Run the chain along the track to the front idler. Wrap the chain around the front idler.
- Attach the chain to the front of the trolley using the master link.
- Tighten the chain until the chain sags about 3 inches (7.6 cm) at the midpoint of the track.
- For retrofit trolley installations, use an additional 16" of chain for the installation.
Install the Header Bracket (Page 18)
The header bracket MUST be RIGIDLY fastened to the structural support on the header wall or ceiling, otherwise the door might NOT reverse when required. DO NOT install the header bracket over drywall. Concrete anchors MUST be used if mounting the header bracket or 2x4 into masonry. NEVER try to loosen, move or adjust the door, springs, cables, pulleys, brackets, or their hardware, ALL of which are under EXTREME tension.
The trolley operator is generally mounted over the center of the door. Off-center mounting may be required due to interfering structures or the location of the door stile or top section support. Typically, the operator may be mounted up to 24 inches (60.1 cm) off center on torsion spring doors. Extension springs require center mounting.
- Close the door. Mark the center of the door with a vertical line and extend the line onto the ceiling.
- Open the door to the highest point of travel and mark 4 inches (10.1 cm) above the highest point of travel.
- Center the header bracket on the vertical center line and the horizontal line.
- Drill the pilot holes for the header bracket.
- Fasten the header bracket with appropriate hardware (not provided).
Attach the Track to the Header Bracket and Hang the Operator (Page 19)
- Align the track with the header bracket.
- Insert the clevis pin through the track and header bracket holes. Secure with the fasteners (clevis pin (1) and keeper rings (2)).
- Swing the operator up and ensure the operator is level.
- Secure the operator using the appropriate fasteners and locking hardware to support the weight of the operator.
To avoid possible SERIOUS INJURY from a falling operator, fasten the operator SECURELY to structural supports of the building, and use concrete anchors if installing ANY brackets into masonry.
Attach the Door Arm and Bracket (Page 20)
- Latch the door arm to the trolley. Make sure the open side of the notch on the door arm faces the door.
- Position the door bracket to the center line of the door and attach the door bracket to the door using appropriate hardware (not included).
Note: when properly installed and adjusted, the door arm should be leaning back toward the operator slightly. Refer to the door manufacturer's instructions for recommended installation guidelines. Hardware (page 20): flanged hex nut 3/8"-16 (2), Nylok nut 3/8"-16 (1), bolt 3/8"-16 x 1" (3).
To prevent possible SERIOUS INJURY from a moving chain: DISCONNECT electric power to the operator BEFORE manually operating your door. If possible, use the emergency disconnect ONLY when the door is CLOSED. NEVER use the emergency disconnect unless the doorway is clear of persons and obstructions.
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), pages 15 to 20.
Jackshaft (JDC), Release (RJDC), and Hoist (JHDC): Assembly and Installation
To prevent possible SERIOUS INJURY, DEATH, or uncontrolled descent of the door (page 21): when installing a jackshaft-style operator on a sectional door, additional precautions MUST be taken to assure that proper door cable tension is present throughout the ENTIRE travel of the door. Also: DO NOT connect electric power until instructed to do so; if the door lock needs to remain functional, install an interlock switch; ALWAYS call an Authorized Service Technician if the door binds, sticks, or is out of balance; NEVER try to loosen, move, or adjust doors, door springs, cable, pulleys, brackets, or their hardware; disable ALL locks and remove ALL ropes connected to the door; fasten the operator SECURELY to structural supports of the building; and use concrete anchors for ANY brackets (page 23).
Carton Inventory (Page 21)
- Operator assembly; hardware box (includes chain keepers and fasteners); installation manual and warning placards
- Floor level wall controller with LCD display
- LiftMaster monitored entrapment protection, CPS-U photoelectric sensors
- Manual release (disconnect) sash chain (RJDC models only)
- Hoist hand chain, and engagement/disengagement ropes (JHDC models only)
- Door/operator drive chain
- Brake release sash chain plus 12 ft extension kit (JHDC 2200 models only)
- JDC7 operators include (2) 4.5 AH batteries and a battery mounting tray. If battery backup is required for other models, order accessory kit DC7AH.
Notes (page 21): the DC logic board includes inputs for cable tension monitors (CTM). They are not required to operate the unit, but LiftMaster highly recommends cable tension monitors (parts K41-0157-000 and K41-0156-000) on standard, vertical, and high lift installations; a CTM detects cable slack and stops and reverses the door. Pusher springs should be used with the door system to help get the door moving in the close direction; for certain doors, such as standard lift, angled track may also be recommended (check with the door manufacturer). Door sprocket kits are sold and shipped separately (see Door Sprockets).
Manual Release (RJDC) Handing Switch, If Required (Page 22)
Tools required (not included): 9/16" socket, 5/16" socket, and a Phillips screwdriver. This procedure re-orients the manual release for the other side of the operator.
- Take off and set aside the plastic cover that houses the manual release assembly by removing 4 securing screws.
- Open the operator's plastic e-box cover and disconnect the switch harness.
- Using a 5/16" socket or Phillips screwdriver, remove the two screws holding the hinge bracket, then slide the assembly out (the screws and subassembly are needed in step 9).
- Remove the screws shown in the figure (only 2, depending on release orientation).
- Unplug the encoder and motor harness. Move the harnesses to prevent cable pinching.
- Remove the eight bolts holding the gearbox to the chassis with a 9/16" socket.
- Remove the gearbox from the assembly and turn it 180 degrees.
- Re-assemble the gearbox to the chassis and secure with eight bolts. Leave the 4 screws on the desired release side loosely installed.
- Re-install the release subassembly to the chassis on the desired side of the operator.
- Tighten all bolts for the gearbox (reference torque 55-60 in-lbs).
- Attach and secure the plastic cover with four screws. Ensure the wire rope exits the plastic cover through the cover slot.
- Connect the encoder and motor harness as shown.
Note: in firmware 1.0 and newer, during commissioning on the LCD wall control, select "REVERSE" in the "MOUNT TYPE" step to ensure proper motor rotation. If the unit is already commissioned, reset to factory settings to see this option.
Configure the Operator (Page 23)
- Place the 10 or 12-tooth drive sprocket on the operator shaft, choosing the appropriate side for your installation. Position the sprocket as close to the operator frame as the installation will allow, then secure with the included set screws.
- MAXUM JDC/JHDC operators are dual-handed; the drive sprocket can be used on either the right or left side. If switching handing, the hoist assembly can also be switched. The hoist changes location depending on the wall mount or front of hood application.
To reposition the hoist: (a) remove the four Allen bolts; (b) pull the housing down and away from the motor, then rotate the housing 180 degrees; (c) place the housing back up to the motor and tighten it back in place using the Allen bolts.
Battery Backup Installation, If Applicable (Page 24)
JDC7 operators include (2) 4.5 AH batteries and a mounting tray; for other models order accessory kit DC7AH. LiftMaster recommends installing the battery backup unit at ground level, prior to mounting the operator in its fixed location.
- Remove the battery cover from the battery enclosure.
- Ensure the jumper and battery harness are properly routed and connected.
- Using the supplied screws, reinstall and secure the battery box cover and ensure the screws are tightened firmly.
- Using the supplied screws, mount the battery enclosure to the operator (or to an appropriate alternate location).
- Route the wires around the backside of the battery enclosure, through the knock out, and into the electrical box. Do NOT connect the wires to the logic board at this time.
- Place the snap-in cord gland over the top of the wires and snap it into place.
Recommended mounting location: JHDC/JDC: side of operator, opposite from the drive shaft and sprocket location; TDC: mount to the bottom of the operator (open the electrical box and knock out the appropriate backside 1/2" conduit location). Knock out location: JHDC/JDC: bottom of the electrical box, adjacent to the EMI filter board; TDC: bottom of the electrical box, adjacent to the antenna AUX connection. Do NOT connect the battery connectors to the printed logic board terminals until instructed (see Commissioning).
Determine the Mounting Location and Mount the Operator (Page 25)
To reduce the risk of severe injury, install the operator a minimum of 8 feet (2.44 m) from the floor. If the operator sprocket is below the 8 foot minimum, install the appropriate chain guard kit for your 2" output shaft (CHNGUARD) or 3" output shaft (CHAINGUARD3IN); chain guard kits are sold separately.
The operator may be mounted on a wall, shelf, or bracket (not provided; see Accessories). The optimum distance between the door shaft and operator drive shaft is 12 to 15 inches (30.5 to 38 cm). The wall or mounting surface MUST be rigid to prevent play between the operator and the door shaft, permit the operator to be fastened securely with the drive shaft parallel to the door shaft, and provide a level base.
- Place the door sprocket on the door shaft so it can be moved to align vertically with the operator drive shaft.
- Insert the keys and fasten the sprockets with the set screws (recommended torque is 34-45 in-lb). LiftMaster highly recommends adding a thread adhesive to secure the set screws.
- Hold the operator in the desired mounting position so the door sprocket and drive sprocket are vertically aligned.
- Mount the operator to the wall or mounting plate, where it can be moved to align, with appropriate hardware (not supplied).
- Wrap the drive chain around the door sprocket and the drive sprocket, then secure with the master link. Chain links may need to be removed to achieve the appropriate chain length.
Installing the Release Chain (RJDC Only) and Securing the Hoist or Release Chain (Page 26)
- Locate the release chain (sash chain) assembly package with the S-hook.
- Loop either end of the S-hook onto the open end of the large spring.
- Use pliers or another crimping tool to close and secure the S-hook end around the spring loop.
- With the sash chain still in the plastic bag, attach the loose end to the S-hook.
- Remove the remaining sash chain from the plastic bag and allow it to hang freely to the floor.
- Cut the sash chain to the desired length.
- Fasten the retaining bracket 4 ft (1.2 m) above the floor. For RJDC models, route the sash chain through the eyelet of the retaining bracket. If the position of the operator causes the hand chain to hang in the door opening, hook the chain to the side near the top of the door jamb.
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), pages 21 to 26.
Manual Release and Emergency Disconnect
To prevent possible SERIOUS INJURY or DEATH from a falling door or arm (page 27): DISCONNECT electric power to the operator BEFORE manually operating your door. DO NOT stand under the door arm when pulling the emergency release. If possible, use the emergency disconnect ONLY when the door is CLOSED. DO NOT pull the disconnect/release sash chain while the door is in motion. DO NOT engage or disengage the hoist mechanism while the door is in motion. NEVER use the emergency release handle unless the doorway is clear of persons and obstructions.
Trolley (TDC) Emergency Disconnect
To disconnect the door from the operator (the door should be fully closed if possible)
- Pull the emergency release handle straight down. The emergency disconnect will open.
To reconnect the door arm to the trolley
- Lift the free end of the door arm to the trolley.
- Pull the emergency release handle to allow the arm to engage the roll pin. Release the handle. The emergency disconnect will close.
RJDC (Manual Release) and JHDC (Hoist) Emergency Disconnect
These operators have provisions for manually operating the door in case of emergency or power failure, and are equipped with a manual hoist. An electrical interlock disables the electrical controls when the hoist is used.
- To disengage and electrically disable the operator controls, pull down and secure the sash chain to the wall bracket (RJDC) or pull the red disengage rope (JHDC). The LCD wall control displays F96 INTERLOCK.
- (2200 models only) Disengage the brake by pulling the sash chain and securing it to the wall bracket.
- For JHDC models only, manually move the door in the desired direction by pulling on one side or the other of the continuous hoist chain loop. (For RJDC models, see page 27 for the manual movement steps.)
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), page 27.
Wiring, Wall Controller, and Entrapment Protection
Power and Ground Wiring (Pages 28)
To prevent possible SERIOUS INJURY or DEATH: ANY maintenance to the operator or in the area near it MUST NOT be performed until the electrical power is disconnected and locked out; when maintenance is complete the area MUST be cleared and secured before the unit is returned to service. Disconnect power at the fuse box BEFORE proceeding. The operator MUST be properly grounded and connected in accordance with national and local electrical codes, and should be on a separate fused line of adequate capacity. DO NOT apply power to the operator until instructed to do so. ALL electrical connections MUST be made by a qualified individual. DO NOT install ANY wiring or attempt to run the operator without consulting the wiring diagram. ALL power wiring should be on a dedicated circuit and well protected; the location of the power disconnect should be visible and clearly labeled. ALL power and control wiring MUST be run in separate conduit.
- Open the electrical box cover.
- Run power wires to the electrical box according to national and local electrical codes (use conduit knockouts and appropriate conduit fittings as indicated on the electrical box label; use caution when removing knockouts to avoid damaging internal components).
- Attach power and ground wires to the appropriate terminals. Incoming power leads go to L1 and L2. Connect the ground wire to GND. The operator must be properly grounded.
Notes: for THREE PHASE POWER, only connect two of the incoming power legs to L1 and L2 and cap off the third leg. Ensure the power disconnect at the panel box can be used as the main disconnect for a single pole, two pole, or three pole application and disengages ALL power legs at the same time. Ensure proper balancing of multi-phase, multi-wire configurations (the electrician is responsible for load balancing). The maximum wire gauge that can be connected to the operator's terminal is 12 AWG; use COPPER WIRE ONLY.
Voltage Selection (Page 28)
LiftMaster offers two types of EMI filter boards, but each operator houses only the type that matches the voltage ordered (type A for 120/240Vac, type B for 480Vac).
- Locate the EMI filter board inside the electrical box.
- Remove the orange voltage sticker covering the voltage connector(s) and stick it to the inside of the electrical box.
- On units with type A EMI filter boards, verify the incoming voltage and phase type.
- Plug the connector into the appropriate plug-in labeled 120Vac OR 240Vac.
Do NOT apply power to the operator until instructed to do so. A mis-selected voltage can damage components (see fault F26 OVER VOLT).
Wall Controller Installation (Page 29)
To prevent possible SERIOUS INJURY or DEATH from electrocution, be sure power is NOT connected BEFORE installing the door control. Install the door control within sight of the door, out of reach of small children, at a minimum height of 5 feet (1.5 m) above landings, steps, or any other adjacent walking surface, and away from ALL moving parts of the door; install the control station far enough from the door to prevent the user from contacting the door while operating the controls; and install the entrapment warning placard next to the control station in a prominent location visible from the door. NEVER permit children to operate or play with door control push buttons or remote controls.
The field wiring terminals are rated for 14 to 24 AWG stranded wire and 12 to 24 AWG solid wire; 300 ft of 24 AWG twisted pair is the recommended maximum run. MAXUM supports connecting only a single LCD wall control (DCWALLCTL); additional single, 2-, or 3-button wall controllers can be connected depending on application needs (see Accessories). The wall control mounting steps and Headless Mode are on page 29 of the original manual.
Monitored Entrapment Protection (Page 30)
The eyes/edge inputs are not functional until the system is commissioned and programmed; the LED on the eyes/edge stays off until then. A monitored entrapment protection device is required for most operation modes; without one, constant pressure to close is required from the wall controller. Three yellow EYE/EDGE terminals are provided on the main board. Connect only ONE set of photo eyes, ONE edge sensor, or ONE light curtain per terminal. For photo eyes, twist both White wires together into a COM terminal and both White/Black stripe wires together into the EYE/EDGE terminal of the same monitored set. Any supported device can be wired into any of the three unoccupied EYE/EDGE terminals.
To prevent possible SERIOUS INJURY or DEATH from a closing door: be sure power is NOT connected BEFORE installing the photoelectric sensors, and the door MUST be fully open or closed BEFORE installing the monitored entrapment protection devices. Correctly connect and align the photoelectric sensor, and install the primary monitored photoelectric sensor beam NO HIGHER than 6" (15 cm) above the floor. This is a required LMEP device for the B2, TS, T, and FSTS wiring types and MUST NOT be disabled.
Install the Monitored Light Curtain, Optional (Page 31)
These steps install one set of monitored light curtains as a standalone primary entrapment protection device. The mounting brackets must be securely fastened to a solid surface such as wall framing; in masonry, add a piece of wood at each location. If the light curtain is installed with a coil cord, secure it so it will not interrupt the light beams.
- Fasten the mounting brackets loosely to both monitored light curtains with the screws provided.
- Measure a maximum of 6 inches above the floor and mark this location. The lowest optical sensor must be installed at or below this point; the light curtain wires must be oriented at the top of the light curtain in this application.
- Hold the monitored light curtain up to the desired mounting location with the cable end pointing upward. Secure the bottom mounting bracket to the mounting surface.
- Make sure the light curtain is level and secure the upper mounting bracket to the mounting surface.
- Tighten the screws to secure the light curtain to the mounting bracket.
- Secure the other light curtain to the opposite side of the door following steps 2 to 5, making sure they are aligned.
- Run wires to the operator.
- Twist like colored wires together, brown to brown and blue to blue. Do not run the wiring in the same conduit with AC power. Disconnect power to the operator before connecting the wires; see page 31 for the power wiring connections.
Install the Cable Tension Monitors, Optional (Page 32)
Two cable tension monitors may be connected to this operator. They detect any slack that may occur in the door cables and respond accordingly. Use only LiftMaster cable tension monitors, which have been tested and approved for this system (see Accessories).
- Make sure the door cable is approximately 1 to 2 inches (25 to 50 mm) from the mounting surface; door adjustments or shimming may be required. The bracket must be flush with the mounting surface.
- Position the cable tension monitor as close to the drum as possible. The optimal distance of the cable from the wall surface is no more than 2.5 inches (6.35 cm), and the roller should extend 1/8 to 1/4 inch past the cable. The monitor and roller must be free of obstructions in all positions of operation, and nothing may prevent the monitor from closing completely when slack is detected.
- Run bell wire to the door operator junction box and down to the control box through SBC conduit. Once the controller is installed, connect the bell wires to the CTM and CMN terminals on the controller (polarity is not important; see the wall controller CTM installation section).
- Cable tension monitors must be anchored to concrete or to a wood stud with appropriate fasteners.
Wiring Diagram (Pages 33 to 38)
LiftMaster says DO NOT install any wiring or run the operator without consulting the wiring diagram; scan the code on page 33 for the digital wiring diagram. Disconnect electric power and/or battery BEFORE installing, performing ANY adjustments, or maintenance, and replace fuses ONLY with the same type and rating (replaceable 30A automotive fuses on the DC input: one pair for 700, two pairs for 1200). The diagram shows the AC junction box, battery box (24Vdc), factory wiring and field wiring conduits, the optional step-down transformers (XF600VAC7, XF600VAC12, XF600VAC22 for 600V; XF208VAC7, XF208VAC12, XF208VAC22 for 208V), accessory power (24VDC, 1A), and dry contact inputs (the INTR LOCK jumper MUST be removed if an interlock switch is added; the STOP-CMN jumper MUST be removed if a stop device is added). The factory and field wiring views are on pages 34 to 38 of the original manual.
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), pages 28 to 38.
Programming and Commissioning
Quick Start Commissioning (Page 39)
To prevent possible SERIOUS INJURY or DEATH: during commissioning, ENSURE the door opening is clear of ALL obstructions. Disconnect electric power BEFORE performing ANY adjustments or maintenance, and wait several seconds for the capacitors to discharge and the display to go out. ALL maintenance MUST be performed by a trained door systems technician.
- CONNECT the battery harness wires to the logic board connector, if battery backup was installed.
- APPLY power to the operator. When power is applied, the LCD display illuminates and steps the user through Quick Start Commissioning.
JDC/JHDC (and RJDC) after a factory reset (firmware v1.21 and earlier) or full factory reset (firmware v2.0 and newer): follow the device menu prompts in this order: select DOOR HANGING; select DOOR SPROCKET; select DOOR DRUM; set MOUNT TYPE (NORMAL or REVERSE; NORMAL is highlighted by default); set OPEN LIMIT; set CLOSE LIMIT; then LEARN Wi-Fi (the operator stays in Wi-Fi Learn Mode for 10 minutes if YES is selected). On a service board the first prompt is the SKU/MODEL option.
TDC (trolley): set MOUNT TYPE (select NORMAL for a standard configuration and REVERSE for a reverse application), set OPEN LIMIT, set CLOSE LIMIT, then LEARN Wi-Fi.
Quick menu shortcuts: to enter the menu, press and hold the Down and red Stop/Enter buttons together for 3 seconds until the screen goes blank. To quick exit a menu, press and hold the Up and red Stop/Enter buttons for 3 seconds. The LCD icons show whether the operator is connected to Wi-Fi, connected to the myQ server (solid) or not connected (blinking), and the battery state (no battery, charging, or fully charged).
Test All Entrapment Protection Devices (Page 40)
It is the responsibility of the specifier, purchaser, installer, and property owner to ensure that, on completion, the entrapment protection devices comply with all relevant federal, state, and local codes and regulations. Keep power applied while testing.
Test the monitored light curtain (if applicable)
- With the door fully open, press the close button.
- While the door is closing, obstruct any of the light beams (the green LED on the light curtain receiver blinks when a beam is obstructed). The door should stop and reverse.
Test the photoelectric sensors (if applicable)
- Open the door. Place an obstruction in the path of the photoelectric sensors. The LMEP LED will blink on the logic board.
- Press and hold the CLOSE button. The door should not close.
- Remove the obstruction.
- Press and hold the CLOSE button. The door should close. If the LMEP is activated while closing, the door should reverse.
Note: the operator remains in C2 mode if photoelectric sensors CPS-RPEN4 and CPS-OPEN4 are not properly aligned.
Additional Programming (Pages 41 to 46)
Enter programming
- Simultaneously press and hold the "Stop/Enter" and "Down" buttons for 3+ seconds to enter the operator menu.
- Scroll down to SYSTEM SETTINGS with the UP and DOWN buttons and press Stop/Enter. You are prompted for the operator passcode.
- Enter 326 as the passcode.
- Door settings (page 41): under SYSTEM SETTINGS, DOOR SETTINGS, select the door type (standard lift, high lift, vertical lift, or rolling), the drum type (required for optimizing the door profile; high lift and full vertical lift are for JDC/JHDC only), and the sprocket (JDC/JHDC only; choose Custom for a non-standard tooth count). For rolling doors, select insulated or non-insulated, height and width (in 2 ft increments, 8 ft up to 28 ft), and the sprocket (50, 60, 72, 82, or Custom).
- Set limits (page 41): go to SYSTEM SETTING, DOOR POSITIONS (open limit, close limit, open mid-stop, close mid-stop, remove open mid, remove closed mid). When commissioning limits for the first time, move the door a few seconds so the encoder starts tracking BEFORE saving the limits; for example, if the door is open, move it down a few inches with the down arrow, then raise it back to the fully open limit before pressing stop to save. The numbers shown while setting limits are encoder markers, not travel distance. For firmware v2.0 and newer, the max run timer is 96 seconds. The operator allows a single mid-stop position.
- Monitored eyes/edge (page 42): devices wired at first power-up are auto-learned, monitoring in the CLOSE direction begins, and the operating mode switches to B2. With no monitored sensor attached, the system defaults to C2. To change a device's direction, go to MONT EYES/EDGES, then the eye/edge number, then DIR. Selecting LEARN ALL relearns devices and reverts the direction to CLOSE, so re-check the direction afterward.
- Cable tension monitor (page 42): view or auto-learn the CTM under SYSTEM SETTINGS, CABLE TNS MONT (AUTO LEARN CTM or LEARN STATUS).
- Operation mode (page 42): change the mode (C2, B2, D2, E2, or timer to close) under SYSTEM SETTINGS, OPERATION MODE.
- Battery options (page 42): for firmware prior to 1.16, AC failure closes the door automatically (DOOR CLOSE) and low battery closes and holds (DOOR CLOSE&HOLD). For firmware 1.16 and newer, there is no automatic door movement on AC failure or low battery (BATTERY RUN, HOLD CLS ON CMD). Change this under SYSTEM SETTINGS, BATTERY OPTIONS.
- Smart position reacquisition (page 42): for firmware 1.21 and newer, if power or position is lost while the door is fully closed, automatic close functions (Timer Secure and myQ schedule) are inhibited, and a user-initiated close command issued before position is re-established may make the operator reverse off the floor and briefly move the door in the open direction.
- Hold position after power reset (page 43, firmware v2.0 and newer): also called "dock leveler mode"; holds the last known door position through a power cycle. Disabled by default; enable under SYSTEM SETTINGS, HOLDPOS ON RESET, ENABLE, SAVE. It returns to disabled after a partial reset or full factory reset.
- Transmitter frequency (page 44): SYSTEM SETTINGS, CONNECTIVITY, LEARN, RX FREQUENCY, select the frequency, save, and exit.
- System info (page 46): the SYSTEM INFO menu shows the system ID, serial number, controller, display, motor, Wi-Fi, and ESARM versions, absolute cycles, door maintenance counts, endpoint ID, open and close limits, door hanging, drum, travel distance, operation mode, timer to close, mid-stop, RX frequency, door sprocket, learned eyes/edges, battery options, and the event log.
Swipe sideways to see all columns.
| Reset option | What it does | What it keeps |
|---|---|---|
| SOFT RESET | Clears no settings; power cycles and restarts the operator from the wall control. | Every configured setting, including learned entrapment protection devices and their protection direction. |
| PARTIAL RESET | Clears door settings, motion settings, learned remotes, Wi-Fi credentials, myQ pairing, entrapment mode, battery, programmable input, and display settings (shows IN PROGRESS for up to 20 seconds). | Learned entrapment protection devices and their protection direction (see page 45 for the complete list). |
| FULL FACT. RESET | Clears every configured setting (shows IN PROGRESS for up to 35 seconds). It cannot be undone. | See page 45 for the list (for example the model number, on production boards). |
Do not remove power while IN PROGRESS is displayed. For firmware v1.21 and earlier, there is a single reset (SYSTEM SETTINGS, passcode, RESET FAC. DEF., SAVE) that resets most user settings to defaults but keeps Wi-Fi credentials, learned remotes/transmitters, absolute cycle count, monitored eyes/edge protection direction, SKU ID, and serial number (page 44); after a reset the operator returns to the quick start commissioning menu and myQ, Wi-Fi, and transmitters are not erased (page 57).
Operating Modes (Pages 47 to 55)
The operator functions in one of four operating modes. The default is B2 when a monitored entrapment protection device is learned, or C2 when none is installed. The tables on pages 48 to 55 give the response of each device (wall controller buttons, single button controls, 3-button remote controls, and myQ Facility) in each door state.
Swipe sideways to see all columns.
| Mode | Behavior as printed |
|---|---|
| B2 | Momentary contact to open, close, and stop with wiring for a sensing device to reverse. Works with the wall controller buttons, myQ Facility, a wired 3-button wall controller, and a 3-button transmitter; single button controls also get stop-and-reverse. A monitored entrapment protection device is required for downward movement; activation reverses the door to its open limit, and an active device can be overridden with 5 seconds of constant pressure on the wall control CLOSE button. Timer to Close (max 999 seconds) and the Car Dealer feature are available in B2. |
| C2 (factory default) | Constant pressure to close, with momentary contact to open and stop; used when no monitored entrapment protection device is installed. |
| D1 | Constant pressure to open and close, with wiring for a sensing device to stop; compatible with 2- or 3-button stations. |
| E2 | Constant pressure to close; the door closes and auto reverses when the button is released (menu entry E2:CNST PRES CL on page 42; see page 51). |
| T / TS | Momentary contact to open, close, and stop with open override and Timer-to-Close (TTC); a monitored entrapment protection device (LMEP) is required. In T mode, the TTC attempts to close the door from any position except fully closed or when an entrapment protection input is present; the stop button recycles the timer, and a defeat switch is required to disable the TTC. |
| FSTS | Available as an operation mode in the menu and for programmable input functions; see pages 48 to 55. |
Remotes, Wi-Fi, and Programmable Inputs (Pages 56 to 60)
- Radio (page 58): the controller has a built-in Security+ 2.0 receiver that can program up to 90 remote controls and up to 30 keyless entries. To learn remotes or myQ devices: SYSTEM SETTINGS (passcode 326), CONNECTIVITY, then Learn myQ Devices or Remotes.
- Security+ 3.0 MAX remotes (page 58): they default to Security+ 3.0, but MAXUM uses Security+ 2.0, so put the remote in programming mode by pressing and releasing its button 6 times within 4 seconds (the red LED stays solid). The door may move during programming; make sure the area is clear.
- Unlearn (page 56): SYSTEM SETTINGS, passcode, CONNECTIVITY, UNLEARN, then REMOTES or MYQ DEVICES, then SAVE.
- Wi-Fi (page 59): SYSTEM SETTINGS, CONNECTIVITY, LEARN, LEARN Wi-Fi puts the operator in Learn Mode. On your device, join the Wi-Fi network named myQ-nnn (the last 3 digits of the operator serial number), then open a browser and go to setup.myqdevice.com or 192.168.1.1 and follow the instructions. To reset Wi-Fi credentials: SYSTEM SETTINGS, CONNECTIVITY, UNLEARN, WI-FI, SAVE.
- Programmable inputs (page 58): four programmable inputs (INP1 to INP4) can be set to non-monitored eye/edge input, timer defeat, X6 car dealer input (for example a loop detector, treadle, or card reader), or FSTS, with a selectable polarity.
- Auxiliary relays kit AUXREL (page 60): the relay adapter board provides N.O. and N.C. contacts (Class 2 low voltage only, 42 Vdc max, 5 amps) set by the AUX RELAY switches (for example open limit, closed limit, door motion).
Documentation note. The operating mode tables on pages 48 to 55 are large matrices of device, action, state, and response whose cell alignment does not extract as text, so the table above summarizes each mode's behavior in words rather than row by row. The mode names also differ between pages: page 8 lists C2, B2, B2/T, B2/TS, D1, E2, and FSTS; page 42's menu lists C2, B2, D2, E2, and timer to close; and page 47 says there are four operating modes.
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), pages 39 to 60.
Troubleshooting and Error Codes
If an error occurs, the idle screen is replaced by a screen showing the error code and a description. Error messages originate in one of three categories: motor drive and power circuitry, option codes related to accessories used with the industrial DC operator, and door control codes related to the motor and encoder. Depending on the error, user interaction may be required to clear it; the error window closes when the error has been cleared or corrected. The tables below summarize the most common causes from the manual's troubleshooting section (pages 61 to 83); the full diagnosis and resolution steps for each code are in the original manual.
Symptom Troubleshooting (Pages 61 to 66)
Swipe sideways to see all columns.
| Symptom | Possible causes listed | What the manual says to check |
|---|---|---|
| Powerhead main board is off (no LEDs lit or blinking) | Transformer overheating; AC power absent or out of range; AC input voltage mis-selected (120V/240V models); blown DC input fuses on the main board; faulty powerhead main board, EMI filter board, transformer, wiring, or rectifier | Let an overheated transformer cool and check door imbalance, ambient temperature, and airflow; verify AC voltage between L1 and L2 at the EMI filter board input; check the EMI filter board output (brown to blue wire); the transformer output winding should read between 22 and 35 volts AC. |
| LCD wall control is off or not functioning | Multiple LCD wall controls wired to one operator; wall control wired to the wrong terminals; no power to the main board; wall control circuit shorted; faulty wiring or wall control | Only one LCD wall control is supported (use the SBC or OPEN, CLOSE, and STOP terminals for additional stations); wire it to the WALL CTRL terminals; check the MAIN PWR and WALL CTRL LEDs; wire at the wall control should measure 11 to 13 volts DC (12VDC at its screw terminals). |
| Main board DC IN fuses blow immediately at power-up | Stray wiring or metal contacting the main board | Inspect the board for stray wiring or metal. |
| Door moves in the wrong direction when pressing the up/down buttons | Reverse mounting mode configured wrong (reverse limits) | Check the MOUNT TYPE setting (NORMAL or REVERSE). |
| Door runs slowly or at half speed | Wall control disconnected or damaged | If communications to the wall control are absent, the system runs at half speed; an LCD wall control is strongly recommended. |
| Operator turns off despite a backup battery being connected | Dead or worn batteries; low battery voltage; blown battery fuses on the main board | Test the batteries and visually inspect or check continuity of the battery fuses. |
| Operator runs momentarily then stops in limit learn mode | Encoder fault or encoder interface fault; encoder wiring fault | In limit learn mode the displayed number is the encoder position; jog the door several inches and the number should change; inspect the encoder cable. |
| No motor movement, cannot set limits, and the wall control shows CHECK STOP CIRCT | STOP input circuit open due to a wiring issue; stuck STOP button on a control station | Check for wiring faults and stuck stop buttons (this does not apply to the LCD wall control). |
| 2200 only: faults F04, F10, and/or F11 with limited door movement, or no faults and limited movement | Sticking or locked brake | Pull the brake sash chain and request a door action; open the e-box and check the brake terminals on the main board (coil not being energized); replace the brake. |
Error Code Table (Pages 66 to 83)
Swipe sideways to see all columns.
| Code | Display message | What it means | Common causes and fixes listed |
|---|---|---|---|
| F02 | F02 OPEN LIMIT | Door has moved beyond the upper end position. | Operator manually hoisted above the upper limit (hoisted jackshaft models); move the position back within normal limits and adjust limits if necessary. |
| F04 | F04 UNAUTH. STOP | No motor motion was detected when the operator attempted to move. | Door drifting upward or imbalanced, obstruction or mechanical jam, motor cable disconnected, worn motor brushes (motor resistance over 3 ohms), main board motor drive fault, encoder wiring fault; on 2200 units a stuck brake. |
| F08 | F08 NO CONFIG | Configuration was not found or was reset to factory settings. | Configure the operator per the normal commissioning process (a new operator, a factory reset, or a partial or full reset on firmware v2.0 and newer). |
| F10 | F10 UP FORCE | Overcurrent condition moving up; the operator senses resistance and stops the door. | Incorrect door speed, operator, or sprocket for the door weight; unbalanced door; pusher springs over tension; worn springs, tracks, rollers, or drums; low voltage at L1/L2. |
| F11 | F11 DOWN FORCE | Overcurrent condition moving down; the operator senses resistance and reverses the door to open. | Same causes as F10; change the speed in the System Settings menu, balance the door, repair drag or binding, and verify voltage at L1/L2. |
| F12 | F12 OVERLOAD UP | Force overload (overcurrent) moving up/open (firmware v1.11 and above). | Verify door weight against the operator rating, check balance at 3 points of travel, check the sprocket, relearn limits with a maximum of 1.5 inches into pusher springs, and check voltage. |
| F13 | F13 OVERLOAD DOWN | Force overload (overcurrent) moving down/close (firmware v1.11 and above). | Same checks as F12, plus a close limit set too aggressively (relearn the close limit so the door does not buckle or over-push on the floor). |
| F14 | F14 SET LIMITS | End positions are not set or stored. | Limits were never set out of the box; set the open and close limits. |
| F19 | F19 SYSTEM ID | System ID is not configured (service kit boards only). | Configure the system ID in the menu using the LCD wall control. |
| F23 | F23 OVERTEMP | Motor drive circuitry temperature is too high; shown until the circuitry cools. | Door imbalance or excessive resistance, poor airflow or ventilation, high ambient temperature, excessive gearbox or motor drag, faulty main board or motor. |
| F26 | F26 OVER VOLT | Motor drive circuitry detected an overvoltage condition. | AC input voltage mis-selected (240V applied while 120V is selected can damage electronics), door imbalance causing motor regeneration, AC power out of range. |
| F31 to F34 | F31 WC OPEN HELD, F32 WC CLOSE HELD, F33 WC STOP HELD, F34 SBC HELD | Wall control buttons held or stuck for at least 1 minute. | Check that all buttons return to the normal state; repair, clean, or replace the controls. |
| F35 to F37 | F35 OPEN HELD, F36 CLOSE HELD, F37 STOP HELD | Input button or device held or stuck for at least 2 minutes. | Inspect the OPEN/CLOSE/STOP terminal wiring for opens or shorts; disconnect accessories one at a time to find a faulty one. |
| F41, F44, F47 | F41 EYE/EDG1 BLK, F44 EYE/EDG2 BLK, F47 EYE/EDG3 BLK | Monitored eye/edge 1, 2, or 3 blocked for 3 minutes or more. | Remove the obstruction; confirm the device is approved and the device type setting matches; check photoeye alignment and emitter wiring. |
| F42, F45, F48 | F42 EYE/EDG1 MIS, F45 EYE/EDG2 MIS, F48 EYE/EDG3 MIS | Monitored eye/edge 1, 2, or 3 was learned but is no longer detected. | Some devices (such as Miller Edge and CPS-OPEN4) show as missing when blocked; check approved devices, device type setting, wiring, and LEDs. |
| F51 to F58 | F51 INP1 BLOCK, F52 INP1 CMND, F53 INP2 BLOCK, F54 INP2 CMND, F55 INP3 BLOCK, F56 INP3 CMND, F57 INP4 BLOCK, F58 INP4 CMND | Unmonitored eye/edge device triggered for 3 minutes or more on input 1, 2, 3, or 4, or blocked when door motion was requested. | Remove the obstruction; check the input configuration; INP1 to INP4 accept dry-contact devices only; check wiring. |
| F61 | F61 CTM FAULT | Cable tension monitor device triggered or missing (cable tension lost). | Check cable tension beneath the CTM roller and that the cables are properly wrapped on the drums; check wiring; swap in a known-good CTM; reset limits and watch for recurrence. |
| F62 | F62 WLESS BLK | Wireless edge blocked. | Remove the obstruction from the wireless edge. |
| F63, F64 | F63 WE BLE MISS, F64 WE BLE MISS | Wireless edge receiver lost BLE communications with the edge (F64 close direction edge, F63 open direction edge). | Pair transmitters to the receiver, replace the transmitter battery, reduce 2.4GHz interference, and check the distance between transmitter and receiver. |
| F65, F66 | F65 WE I2C MISS, F66 WE I2C MISS | Wireless edge is configured but the main board cannot communicate with the receiver (F66 close direction edge, F65 open direction edge). | Intermittent or complete loss of signal; check the receiver connection. |
| F68 | F68 WE CRITBATT | Wireless edge transmitter has a low battery. | Replace the battery in the wireless edge transmitter. |
| F89 | F89 WC DISC | Wall control is not detected. | The wall control may be intentionally disconnected, or wired but off or not functional; LiftMaster strongly recommends using an LCD wall control. |
| F91 | F91 ENCODER | The system detected irregularities in the signals received from the encoder (direction of rotation incorrect). | Check the mount type and the encoder; a system ID mismatch between the main board and chassis can cause the encoder not to be recognized. |
| F95 | F95 MOTOR COMM | Message with invalid format received from the motor MCU. | Power cycle the operator; if it persists, reset to factory defaults and reconfigure; if it still persists, replace the powerhead main board. |
| F96 | F96 INTR LOCK | The interlock circuit was broken; the motor drive circuit is disabled while the INTR LOCK circuit is open. | The hoist is engaged (manual hoist models) or the J-disconnect interlock switch is open; operators without a manual hoist include a jumper to bypass the interlock connections. |
| F101 | F101 BBU LOW | Battery is present but discharged (voltage is low). | Allow the battery to charge or replace it. |
| F102 | F102 BBU DISCONN | Battery is learned to the system but is not detected. | Verify battery wiring, polarity, and terminals; test the batteries; check the battery fuses. |
| F105 | F105 AC FAIL | AC failure; the system is running on battery. | Power outage or input voltage outside specifications. |
| F106 | F106 WC SHORT | Wall control is removed and jumpered out, or shorted. | Wall control intentionally disconnected, wiring short circuit, or damaged wall control. |
| F120 | F120 MAINT DUE | Maintenance counter reached the preset limit. | Perform the maintenance and reset cycles (see the maintenance reset procedure on page 57). |
| F121 | F121 OVER CYCLED | Cycle count hourly limit reached. | The operator was cycled more than the hourly limit. |
Documentation note. Page 27 says the LCD displays "F96 INTERLOCK" when the hoist or release is engaged, while the error table on page 82 lists the message as "F96 INTR LOCK". The code table above summarizes causes in brief; where the manual's diagnosis and resolution columns have several steps, follow the full steps on the pages cited before replacing parts.
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), pages 61 to 83.
Maintenance
To avoid SERIOUS personal INJURY or DEATH (page 84): disconnect electric power BEFORE performing ANY adjustments or maintenance. ALL maintenance MUST be performed by a trained door systems technician.
Maintenance Schedule (Page 84)
For use with the Maintenance Alert System. Check at the intervals listed in the manual's chart: every month, every 3 months or 5,000 cycles, and every 6 months or 10,000 cycles. The check marks that place each item in a column are graphics on page 84, so refer to that chart for which interval applies to which item.
Swipe sideways to see all columns.
| Item | Procedure |
|---|---|
| Drive chain | Check for excessive slack. Check and adjust as required. Lubricate. |
| Sprockets | Check set screw tightness. |
| Fasteners | Check and tighten as required. |
| Manual hoist (if applicable) | Check and operate. |
| Shafts | Check for wear and lubricate. |
| LiftMaster monitored entrapment protection | Check alignment and functionality. |
Use SAE 30 oil (never use grease or silicone spray). Do not lubricate the motor; the motor bearings are rated for continuous operation. Inspect and service whenever a malfunction is observed or suspected. For the maintenance reset (RESET CYCLES and MAINTENANCE COMPLETE), see page 57; only a certified door installer should perform it after replacing parts and/or performing maintenance.
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), pages 57 and 84.
Accessories and Service Parts
The tables below list accessories and service parts as printed on pages 85 to 91. The links open related All Security Equipment category pages and do not by themselves confirm that we stock a part or that it fits your operator.
Accessories (Pages 85 to 88)
The manual's accessories pages show photoelectric sensors (CPS-U included as standard with every MAXUM operator, CPS-UN4, CPS-OPEN4, CPS-RPEN4), pneumatic and optical sensing edges (65-8202, 65-5202, OES-SD16, OES-SD24, OES-RD16), light curtain and power supply accessories, wall controllers (DCWALLCTL, included with new MAXUM operators), remote controls and keypads (850LM, 860LM, 878MAX, 811LMX, 891LMMC, 893MAX), loop detectors (LPEXP and LOOPDETLM, both required), traffic lights (RGL24LY, RGL-CTL, which require the AUXREL card), the auxiliary relay board AUXREL, interlock switches, motion detectors, and antenna extension kits (86LM, 86LMT). On several of these pages the part numbers and descriptions are laid out in a graphic grid whose pairings do not extract as text, so check page 85 to 87 of the original manual for which part number goes with which accessory.
Swipe sideways to see all columns.
| Part number | Description |
|---|---|
| DC7AH | 7 AH battery backup kit |
| CHNGUARD | Chain guard kit for 2" output shafts |
| CHAINGUARD3IN | Chain guard kit for 3" output shafts |
| CHAINTENSDC | 1" chain tensioner (spreader bar) |
| CHAINTENS125DC | 1.25" chain tensioner (spreader bar) |
| 001A3982 | Operator cover for 700/1200 operators |
| COVERDC | Operator cover for all MAXUM wall mount models |
| XF600VAC7 | 600V transformer kit for 700 operators |
| XF600VAC12 | 600V transformer kit for 1200/2200 operators |
| XF208VAC7 | 208V transformer kit for 700 operators |
| XF208VAC12 | 208V transformer kit for 1200/2200 operators |
| 312HM | 315 MHz universal radio receiver |
| 412HM | 390 MHz universal radio receiver |
| HTR120NC | Heater kit for all MAXUM operators; no cover required; requires separate 120VAC power |
| 71-1550B10LGH | 10-tooth operator sprocket kit, 1 in. bore x 1/4 in. keyway; replaces the 12-tooth drive sprocket to reduce speed 20% |
| K41-0156-000 and K41-0157-000 | Cable tension monitors (left and right; see pages 21 and 86) |
Trolley (TDC) Service Parts (Page 89)
Swipe sideways to see all columns.
| Part number | Description |
|---|---|
| K41-0373-000 | 20-tooth drive sprocket #48 (TDC7) |
| K41-0372-000 | 20-tooth drive sprocket #41 (TDC12) |
| K41-0564-000 | 16-tooth drive sprocket #41 (TDC12/TDC22) |
| K41-0552-000 | Operator frame (for TDC 700 and 1200) |
| K41-0482-000 | Frame for TDC 2200 |
| K41-0562-000 | Motor cap for TDC 2200 |
| K75-10170 | Trolley |
| K75-10174 | Front idler assembly |
| K75-10259 | Track spacer |
| K10-10205 | Header bracket |
| K41-0565-000 | Header pivot pin |
| K75-12870 | Door arm kit (curved arm, straight arm, door bracket, and hardware) |
| K11-10197 | Take-up bolt, 5/16" |
| K004-0079-000 | Take-up bolt, 3/8" |
| K75-17034 | Heavy duty straight arm |
Door drive chain kits (page 89) include TDC48-08, TDC48-10, and TDC48-12 for the #48 chain on TDC 700 (doors to 8, 10, and 12 ft) and TDC41-10 for the #41 chain on TDC 1200 and 2200 (doors to 10 ft); see page 89 for the full list. Door track is sold separately (call for pricing and availability).
Hoist (JHDC) and Release (RJDC) Service Parts (Page 90)
Swipe sideways to see all columns.
| Part number | Description |
|---|---|
| 1910929FT12 | Hoist chain, 12 ft length (JHDC) |
| 1910929FT25 | Hoist chain, 25 ft length (JHDC) |
| K41-0269-000 | Disengage and engage ropes, 15 ft length (JHDC) |
| K41-0549-000 | Disengage and engage ropes, 29 ft length (JHDC) |
| K41-0479-000 | Hoist assembly with red/green ropes, no hoist chain (JHDC 700, 1200, and 2200) |
| K41-0480-000 | Operator frames, left and right sides (JHDC 2200) |
| K41-0539-000 | Motor, gear box, and encoder (RJDC7) |
| K41-0541-000 | Operator frame (RJDC7) |
| K41-0542-000 | Manual release subassembly (RJDC7) |
| K41-0548-000 | Plastic cover only for the manual release (RJDC7) |
Common Service Kits (Page 91)
Swipe sideways to see all columns.
| Part number | Description |
|---|---|
| K41-0381-000 | Toroidal transformer, 700 / 120VAC-240VAC |
| K41-0382-000 | Toroidal transformer, 700 / 480VAC |
| K41-0383-000 | Toroidal transformer, 1200 / 120VAC-240VAC |
| K41-0384-000 | Toroidal transformer, 1200 / 480VAC |
| K41-0386-000 | Toroidal transformer, 2200 / 120VAC-240VAC |
| K41-0478-000 | Bridge rectifier, 2200 |
| K77-36541 | Antenna |
| K41-0424-000 | Encoder (with drive sprocket, snap ring, mounting plate, and screws) |
Page 91 also lists the motor, gear box, and encoder kits for each model (J/H 700 with or without a 3 in. shaft, JHDC12S, JHDC12X, JHDC22X, TDC7S, TDC12S, TDC12X, and TDC22X) and the main board for all MAXUM operators; the pairing of kit numbers to models is laid out in a grid, so order those from the page 91 table.
Shop related items: commercial door operator parts | commercial door operator accessories | trolley commercial door operators | hoist commercial door operators | jackshaft commercial door operators
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), pages 85 to 91.
Warranty
Per LiftMaster's limited warranty for MAXUM (page 92), the warranty period starts from the date of purchase. Where a period is measured by both time and operator cycles, both parameters are considered at the time of a claim, and if one is not met the limited warranty will not apply. Cycle count measurement begins at the start of the warranty period, but cycle counts are not used to determine eligibility until the first two years have ended. Where an accurate cycle count is unavailable (for example after replacing a part critical to determining the count), the warranty period expires at the end of the first two years from the installation date.
Swipe sideways to see all columns.
| Item | Warranty period |
|---|---|
| MAXUM operator, standard duty | 5 years / 85,000 cycles |
| MAXUM operator, extended or continuous duty | 5 years / 130,000 cycles (extended: units manufactured with firmware 1.17 and prior; continuous: firmware 1.21 and later) |
| Battery backup kit | 1 year |
| Photoeyes | 1 year |
| Replacement parts | 1 year |
| LCD wall control | 2 years |
Proper operation depends on complying with the instructions for installation, operation, maintenance, and testing of the product and associated door hardware; failure to comply strictly will void the limited warranty in its entirety. If the product appears to contain a covered defect, LiftMaster says to call 1-800-528-2806 (toll free) before dismantling the product and you will be advised of disassembly and shipping instructions. The warranty covers defective original manufactured parts and is not valid for replacement or repair of any part that is not the original manufactured part; you are responsible for removal and reinstallation costs. The complete terms and exclusions are printed on page 92.
Documentation note. Our hoist and jackshaft product pages list a 2 year operator warranty and a 2 year motor warranty, while the manual's warranty table (page 92) and our trolley product page list 5 years / 85,000 cycles for standard duty and 5 years / 130,000 cycles for extended duty. Confirm the current warranty with LiftMaster for the model you are buying. The manual's warranty text also refers to "the residence in which this product is originally installed," although the cover marks these operators not for residential use.
All Security Equipment note. If you bought a MAXUM operator from All Security Equipment, see our refund policy and Help Center for how manufacturer warranty returns are handled.
Source: LiftMaster Installation Manual 114-6042-000 (Rev. I), page 92.
Frequently Asked Questions About LiftMaster MAXUM Commercial Door Operators
What is the MAXUM line?
LiftMaster's industrial DC operators for commercial doors: jackshaft (JDC and RJDC), hoist (JHDC), and trolley (TDC) models for doors up to 700, 1,200, and 2,200 lbs. They are not for residential use. See Overview.
How do I choose between the jackshaft, hoist, and trolley?
The jackshaft and hoist mount beside the door shaft and drive it with a chain and door sprocket; the hoist adds a manual hoist chain. The trolley hangs from a header bracket and drives a trolley along a track with a door arm. See Which MAXUM Operator Do You Have?
How do I read a MAXUM model number?
Use the model decoder: type (J, RJ, JH, or T), door weight (7, 12, or 22), duty cycle (S or X), voltage (1 or 4), battery backup (B), and shaft or handing codes (page 6). See Model Decoder.
Which door sprocket do I need?
It depends on the door type, drum diameter or door weight, and desired speed. If you are unsure of a sectional door drum diameter, choose the 32-tooth door sprocket. See Door Sprockets.
How high must the operator be mounted?
At least 8 feet (2.44 m) from the floor; below that, install a chain guard kit (page 25). See Mount the Operator.
What voltages are supported?
120/240V single and 3 phase and 480V 3 phase as dedicated SKUs; 208V and 600V 3 phase through accessory step-down transformers (page 6). See Voltage Selection.
Are photo eyes required?
Monitored photoelectric sensors and/or door edge sensors are required for momentary contact to close modes. Without one, constant pressure to close is required from the wall controller. A CPS-U photo eye kit is included with each MAXUM operator. See Entrapment Protection.
How do I commission the operator?
Apply power and follow the LCD Quick Start prompts: door hanging, sprocket, drum, mount type, open limit, close limit, and Wi-Fi. See Quick Start Commissioning.
How do I get into the programming menu?
Press and hold the Stop/Enter and Down buttons for 3 seconds, choose SYSTEM SETTINGS, and enter the passcode printed in the manual (page 41). See Additional Programming.
How do I move the door by hand?
Trolley: pull the emergency release handle straight down. RJDC: pull down and secure the sash chain. JHDC: pull the red disengage rope and use the hoist chain. Always disconnect power first and use the release only when the door is closed if possible (page 27). See Manual Release.
How do I connect it to Wi-Fi and myQ?
Use SYSTEM SETTINGS, CONNECTIVITY, LEARN, LEARN Wi-Fi, then join the myQ-nnn network on your device and go to setup.myqdevice.com (page 59). See Remotes, Wi-Fi, and Programmable Inputs.
What do the F-codes mean?
Each code is explained in the error code table (pages 66 to 83). See Error Code Table.
What maintenance does it need?
Check the drive chain, sprocket set screws, fasteners, manual hoist, shafts, and entrapment protection at the scheduled intervals, lubricating with SAE 30 oil only and never lubricating the motor (page 84). See Maintenance.
Is the manual available in other languages?
The PDF has the English manual first (pages 1 to 92), followed by French and Spanish. This page presents the English version.
Original LiftMaster Documentation
This HTML resource is presented by All Security Equipment, is not a LiftMaster publication, and does not replace the original manufacturer documentation. It is based on LiftMaster's Installation Manual for the Industrial DC Operators, Models JDC, RJDC, JHDC, and TDC, document 114-6042-000 (Rev. I), ©2026 The Chamberlain Group LLC.
- LiftMaster MAXUM Installation Manual (114-6042-000, Rev. I): the document this page is based on (English on pages 1 to 92).
- LiftMaster MAXUM jackshaft commercial door operator product page at All Security Equipment
- LiftMaster MAXUM hoist commercial door operator product page at All Security Equipment
- LiftMaster MAXUM trolley commercial door operator product page at All Security Equipment
The manual itself says the latest installation manual can be found at liftmaster.com and at support.partner.liftmaster.com. Check LiftMaster's website for the current revision before relying on any document, because LiftMaster may update them.
Related Resources
- Commercial door operators
- Jackshaft commercial door operators
- Hoist commercial door operators
- Trolley commercial door operators
- Commercial door operator accessories
- Commercial door operator parts
- All LiftMaster products
Need the operator itself? All Security Equipment sells the LiftMaster MAXUM commercial door operators.
This resource was last updated November 19, 2026. Based on LiftMaster document 114-6042-000 (Rev. I).
