LiftMaster 2220L Basic Series chain drive garage door opener with integrated camera LiftMaster 2420L Basic Series chain drive garage door opener with integrated camera and battery backup
LiftMaster 2220L (left) and LiftMaster 2420L (right) Basic Series garage door openers. Product images from All Security Equipment.

Documentation Information

Manufacturer
LiftMaster (Chamberlain Group, LLC)
Series and models
Basic Series: 2100L, 2220L, 2300L, 2420L (All Security Equipment carries the 2220L and 2420L)
Equipment type
Residential garage door openers with myQ Wi-Fi (residential use only)
Document type
User's Guide (English and French in one PDF; this page presents the English version, pages 1 to 18)
Manufacturer document number
114-6138-000
Manual revision
Rev. C (printed as 114-6138-000 (Rev. C))
Manual copyright / publication
©2026 Chamberlain Group, LLC. The manual does not print a separate revision date.
Source
LiftMaster Basic Series User's Guide; see Original LiftMaster Documentation
HTML resource last updated
November 11, 2026

Common tasks: Compare the four models | Connect to Wi-Fi and myQ | Program a remote | Set the open and close positions | Test safety reversal | Troubleshoot

LiftMaster Basic Series Garage Door Opener Overview

LiftMaster sells its residential garage door openers in three series: Basic, Plus, and Premium. The Basic Series has four models, and LiftMaster covers all four in one User's Guide (document 114-6138-000): the 2100L, the 2220L, the 2300L, and the 2420L. All Security Equipment carries two of them, the LiftMaster 2220L and the LiftMaster 2420L, so this page focuses on those two while keeping the guide's information for the other two models in context.

LiftMaster's guide is for residential use only. It says the garage door opener comes with a pre-programmed remote control, is compatible only with myQ and Security+ 3.0 accessories, and will not close the door unless the Protector System (safety reversing sensors) is connected and properly aligned. The guide is a User's Guide; it covers setup, operation, adjustments, maintenance, and safety, and refers you to support.chamberlaingroup.com for the complete manual (see the note at the end of Installation).

The Four Basic Series Models

The guide's cover and sections identify the models by feature, and its warranty table lists the warranty periods (page 15). The model features below are only those the guide states.

Swipe sideways to see all columns.

LiftMaster Basic Series models covered by the User's Guide (cover, pages 7, 9 and 15)
Model Camera Battery backup Sold by All Security Equipment
2100L No (the guide lists camera set up for the camera models only) No No
2220L Yes (cover: "Model: 2220L, 2420L (Camera)") No (the guide lists battery backup for the 2300L and 2420L only) Yes, LiftMaster 2220L
2300L No Yes (page 9: "Model 2300L, 2420L") No
2420L Yes Yes Yes, LiftMaster 2420L

Documentation note. The cover and the camera and battery sections name the 2220L, but the warranty table on page 15 lists "2100L, 2200L, 2300L, and 2420L" and has no 2220L row. This page treats "2200L" as a likely typo for the 2220L and does not assume the 2220L's warranty terms from that row. For the 2220L, All Security Equipment's product page lists a 5 year motor warranty and a 1 year camera, parts, and accessories warranty (see Warranty).

The Two Models We Carry

  • LiftMaster 2220L: per our product page, a 3/4 HP DC chain drive opener with an integrated camera and Wi-Fi, with a three-button transmitter (L993S) and a multi-function wall control (L955W). It does not include a battery backup.
  • LiftMaster 2420L: the model in the Basic Series with both the integrated camera and the battery backup, per LiftMaster's guide. Our 2220L page directs buyers who need an integrated battery backup to the 2420L.

All Security Equipment note. Prices, included remotes and wall controls, and warranty details for each model are on its product page. The User's Guide describes functions common to the series and does not state horsepower, drive type, or what ships in each box.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, cover and page 1.

Back to contents

Important Safety Information

Safety Symbols and Unattended Operation

The guide says the garage door opener was designed and tested to offer safe service provided it is installed, operated, maintained, and tested in strict accordance with its instructions and warnings. Its safety symbols mark mechanical and electrical hazards (WARNING, which alerts you to the possibility of serious injury or death), and the CAUTION signal word alerts you to possible damage to the garage door or opener. The guide includes a California Proposition 65 warning (this product can expose you to chemicals including lead; www.P65Warnings.ca.gov). It adds that the images in the guide are for reference only and your product may look different.

Unattended operation (LiftMaster, page 2): the Timer-to-Close (TTC) feature, the myQ app, and the myQ Garage Door and Gate Monitor are examples of unattended close and are to be used ONLY with sectional doors. Any device or feature that allows the door to close without being in the line of sight of the door is considered unattended close. DO NOT install on a one-piece door if using devices or features providing unattended close.

Important Safety Instructions for Installation (Page 3)

To reduce the risk of SEVERE INJURY or DEATH:

  1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.
  2. Install the garage door opener ONLY on a properly balanced and lubricated garage door. An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH.
  3. ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing the opener.
  4. Disable ALL locks and remove ALL ropes connected to the garage door BEFORE installing the opener to avoid entanglement.
  5. Where possible, install the door opener 7 feet (2.13 m) or more above the floor.
  6. Mount the emergency release within reach, but at least 6 feet (1.83 m) above the floor and avoiding contact with vehicles to avoid accidental release.
  7. NEVER connect the garage door opener to a power source until instructed to do so.
  8. NEVER wear watches, rings or loose clothing while installing or servicing the opener.
  9. Install the wall-mounted garage door control within sight of the garage door, out of reach of small children at a minimum height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of the door.
  10. Place the entrapment warning label on the wall next to the garage door control in a prominent location.
  11. Place the emergency release/safety reverse test label in plain view on the inside of the garage door.
  12. Upon completion of installation, test the safety reversal system. The door MUST reverse on contact with a 1-1/2" (3.8 cm) high object (or a 2x4 laid flat) on the floor.
  13. To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric and battery power BEFORE performing ANY service or maintenance.
  14. DO NOT install on a one-piece door if using devices or features providing unattended close. Unattended devices and features are to be used ONLY with sectional doors.
  15. SAVE THESE INSTRUCTIONS.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, pages 2 and 3.

Back to contents

Power and Wiring (Page 3)

To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: be sure power is NOT connected to the opener, and disconnect power to the circuit BEFORE removing the cover to establish a permanent wiring connection. Garage door installation and wiring MUST be in compliance with ALL local electrical and building codes. NEVER use an extension cord or 2-wire adapter, or change the plug in ANY way to make it fit the outlet. Be sure the opener is grounded.

The opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet; if it doesn't fit, contact a qualified electrician to install the proper outlet.

Option A, typical wiring

  1. Plug in the garage door opener into a grounded outlet.
  2. DO NOT run the garage door opener at this time.

Option B, permanent wiring (if required by your local code)

To make a permanent connection through the 7/8-inch hole in the top of the motor unit (according to local code):

  1. Be sure power is NOT connected to the opener and disconnect power to the circuit.
  2. Remove the motor unit cover screws and set the cover aside.
  3. Cut the power cord 6 inches (15.2 cm) from the top of the garage door opener.
  4. Remove the strain relief.
  5. Pull the power cord wires back into the garage door opener.
  6. Install a conduit or flex cable adapter in the 7/8-inch hole.
  7. Run the permanent wires through the conduit in the 7/8-inch hole. Strip the insulation from the ends of all wires.
  8. Connect the black (line) wire to the existing black wire, the white (neutral) wire to the existing white wire, and the ground wire to the existing green ground wire with wire nuts. The opener must be grounded.
  9. Properly secure the wires with plastic ties so that the wires do not come in contact with moving parts.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, page 3.

Back to contents

Important Safety Instructions for Operation (Page 4)

To reduce the risk of SEVERE INJURY or DEATH:

  1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.
  2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door control push buttons or remote controls.
  3. ONLY activate the garage door when it can be seen clearly, it is properly adjusted, and there are no obstructions to door travel.
  4. ALWAYS keep the garage door in sight and away from people and objects until completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
  5. NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY OPENED DOOR.
  6. If possible, use the emergency release handle to disengage the trolley ONLY when the garage door is CLOSED. Use caution when using this release with the door open. Weak or broken springs or an unbalanced door could result in an open door falling rapidly and/or unexpectedly and increasing the risk of SEVERE INJURY or DEATH.
  7. NEVER use the emergency release handle unless the garage doorway is clear of persons and obstructions.
  8. NEVER use the handle to pull the garage door open or closed. If the rope knot becomes untied, you could fall.
  9. After ANY adjustments are made, the safety reversal system MUST be tested.
  10. ALWAYS KEEP THE GARAGE DOOR PROPERLY BALANCED.
  11. ALL repairs to cables, spring assemblies and other hardware, ALL of which are under EXTREME tension, MUST be made by a trained door systems technician.
  12. To avoid interference with the proper operation of the opener when using a welder in the garage, unplug the opener before operating the welder.
  13. To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric and battery power BEFORE performing ANY service or maintenance.
  14. This operator system is equipped with an unattended operation feature. The door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
  15. DO NOT install on a one-piece door if using devices or features providing unattended close.
  16. SAVE THESE INSTRUCTIONS.

LiftMaster's page 4 also prints an FCC and Innovation, Science and Economic Development Canada notice: the device complies with part 15 of the FCC rules, is a Class B digital device, must be installed to maintain at least 20 cm (8 in.) between users or bystanders and the device, and changes not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Reese's Law: Coin Battery Warning (Page 16)

INGESTION HAZARD: this product contains a button cell or coin battery (CR2032, 3 V). Death or serious injury can occur if ingested. A swallowed button cell or coin battery can cause internal chemical burns in as little as 2 hours. KEEP new and used batteries OUT OF REACH of CHILDREN. Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body. Remove and immediately recycle or dispose of used batteries according to local regulations; do not dispose of batteries in household trash or incinerate. Non-rechargeable batteries are not to be recharged. Ensure the batteries are installed correctly according to polarity, do not mix old and new batteries or different types, and always completely secure the battery compartment; if it does not close securely, stop using the product, remove the batteries, and keep them away from children. Call a local poison control center for treatment information.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, pages 4 and 16.

Back to contents

myQ App Control and Wi-Fi Setup

All four models are Wi-Fi connected (page 5). LiftMaster says myQ app account registration and a Wi-Fi connection are required before commencing garage door opener installation (cover). myQ app control will NOT work if the garage door opener is operating on battery power (page 5).

What You Will Need

  • A Wi-Fi and Bluetooth enabled smartphone, tablet, or laptop.
  • A broadband internet connection.
  • A Wi-Fi signal in the garage (2.4 GHz, 802.11b/g/n required).
  • The password for your home network (the router's main account, not the guest network).
  • The myQ serial number located on the garage door opener.

Download the App and Connect

Open and close your door, get alerts, and set schedules from anywhere. Connected smart garage door openers also receive software updates. The garage door opener must run through a complete cycle before it will activate Wi-Fi programming.

  1. Download the myQ app (the guide gives a QR code on its cover for the free app).
  2. Set up an account and connect.

If you already have the myQ app installed: check that your mobile device has the latest software, and download the latest version of the myQ app. For more information, visit support.chamberlaingroup.com.

Test the Wi-Fi Signal Strength

Make sure your mobile device is connected to your Wi-Fi network. Hold your mobile device in the place where your garage door opener is installed and check the Wi-Fi signal strength. LiftMaster says: if the signal is strong, you are all set and can install your new garage door opener; if the signal is weak, the opener will likely connect, and if not, try one of the options below; if there is no Wi-Fi signal, move your router closer to the garage door opener to minimize interference from walls and other objects, or buy a Wi-Fi range extender.

Wi-Fi Status LED

An LED on the garage door opener indicates Wi-Fi status.

Swipe sideways to see all columns.

Wi-Fi status LED (page 5)
LED Definition
Blue, off Wi-Fi is not turned on.
Blue, blinking Garage door opener is in Wi-Fi LEARN mode.
Blue, solid Mobile device connected to the garage door opener.
Blue and green, blinking Attempting to connect to router.
Green, blinking Attempting to connect to the internet server.
Green, solid Wi-Fi has been set up and the garage door opener is connected to the internet.

If you cannot connect, LiftMaster says to make sure the myQ serial number was entered correctly (the characters are A to F and 0 to 9 only) and try again (page 14).

Source: LiftMaster User's Guide 114-6138-000 Rev. C, page 5.

Back to contents

Programming Remote Controls and Keyless Entry

A pre-programmed remote control is included, so there is no need to program that remote (page 6). To add or reprogram a remote control, follow the instructions below. LiftMaster states that older LiftMaster remote controls are NOT compatible and that this garage door opener is only compatible with Security+ 3.0 remote transmitters and wireless keypads.

Program a Remote Control or Wireless Keypad

  1. Lift the push bar. Press the LEARN button twice (after the second press, the LED on the door control panel will pulse repeatedly).
  2. 2a, remote control: within 30 seconds, press and hold the button on the remote control that you wish to use. Release the button when the garage door opener lights flash and/or two clicks are heard.
    2b, wireless keypad: within 30 seconds, enter a 4-8 digit personal identification number (PIN) of your choice. Press and hold the HOME button until the garage door opener lights flash and/or two clicks are heard.

Test for success: to operate the garage door opener, press the remote button you programmed; the garage door should activate. If it does not, repeat the programming steps. Alternatively, with the garage door closed, enter the PIN you programmed and press the HOME button; the garage door will then open. If it does not open, repeat the programming steps.

Program Using the Garage Door Opener LEARN Button

  1. Locate the LEARN button.
  2. Press and immediately release the LEARN button. The LEARN LED will glow steady for 30 seconds.
  3. Remote control: press and hold the button on the remote control that you wish to use.
    Keyless entry: enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad, then press and hold the ENTER button.
  4. Release the button when the garage door opener lights blink or two clicks are heard.

Documentation note. The keypad method on page 6 says to enter a 4-8 digit PIN and press HOME, while the LEARN button method says to enter a 4-digit PIN and press ENTER. The guide does not say which keypad models use which method; check the instructions that came with your keypad.

The opener is compatible with HomeLink versions 4, 5 and 6. HomeLink programming and support can be obtained by contacting HomeLink directly at 1-800-355-3515 or at www.HomeLink.com (pages 6 and 14).

Source: LiftMaster User's Guide 114-6138-000 Rev. C, page 6.

Back to contents

Camera (2220L and 2420L)

The 2220L and the 2420L are the camera models in the Basic Series (cover and page 7). To set up the camera, download the myQ app and set up your account, then follow the instructions in the app to set up and use the camera. For more information on using the camera, visit support.chamberlaingroup.com. myQ app control and the camera will NOT work if the garage door opener is operating on battery power.

Camera Status LED

During the camera set up process the LED color changes as it progresses through each state.

Swipe sideways to see all columns.

Camera status LED (page 7)
LED Definition
Flashing blue Camera is attempting to connect to the mobile device.
Solid blue Camera is connected to the mobile device.
Flashing blue and green Camera is attempting to connect to the router.
Flashing green Camera is connected to the router and attempting to connect to the myQ server.
Solid green Camera is connected and working normally.
Solid white Camera is powering up.
Flashing red Camera is overheating.
Flashing purple Camera firmware is updating.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, page 7.

Back to contents

Operation

Erase the Memory

Erase all remote controls and keyless entries

  1. Press and hold the LEARN button on the garage door opener until the LEARN LED goes out (approximately 6 seconds). All remote control and keyless entry codes are now erased. Reprogram any accessory you wish to use.

Erase all devices, including myQ enabled accessories

  1. Press and hold the LEARN button on the garage door opener until the LEARN LED goes out (approximately 6 seconds).
  2. Immediately press and hold the LEARN button again until the LEARN LED goes out. All codes are now erased. Reprogram any accessory you wish to use.

Erase the connection from the garage door opener to the home Wi-Fi network

  1. Press and hold the black adjustment button on the garage door opener until 3 beeps are heard (approximately 6 seconds).

Open the Door Manually and the Lockout Feature

To prevent possible SERIOUS INJURY or DEATH from a falling garage door: if possible, use the emergency release handle to disengage the trolley ONLY when the garage door is CLOSED. Weak or broken springs or an unbalanced door could result in an open door falling rapidly and/or unexpectedly. NEVER use the emergency release handle unless the garage doorway is clear of persons and obstructions. NEVER use the handle to pull the door open or closed. If the rope knot becomes untied, you could fall.

To open the door manually

Disengage any door locks before proceeding.

  1. The door should be fully closed if possible.
  2. Pull down on the emergency release handle.

Lockout feature

  1. Pull the emergency release handle down and back. The door can then be raised and lowered manually.
  2. To disengage the lockout feature, pull the handle straight down. The trolley will reconnect the next time the opener is activated.

Multi-Function Control Panel

LiftMaster's illustration of the door control (page 8) labels the push bar, light button, command LED (amber), and LEARN button. The battery status LED is described under Battery Backup. When the opener is plugged in and the door control is installed and wired correctly, the command LED on the control panel will glow solid (page 10).

Source: LiftMaster User's Guide 114-6138-000 Rev. C, page 8.

Back to contents

Battery Backup (2300L and 2420L)

Battery backup applies to the 2300L and the 2420L (page 9). The 12V battery backup allows access in and out of your garage even when the power is out. The battery does not have to be fully charged to operate the opener. When the opener is operating on battery power, it may run slower, and these features are disabled: the garage door opener lights, myQ app control and monitoring, and unattended close including Timer-to-Close.

To reduce the risk of FIRE or INJURY to persons: disconnect ALL electric and battery power BEFORE performing ANY service or maintenance. Use ONLY LiftMaster part #485LM for the replacement battery. DO NOT dispose of the battery in fire; the battery may explode. Check with local codes for disposal instructions. ALWAYS wear protective gloves and eye protection when changing the battery or working around the battery compartment.

Install the Battery

  1. Unplug the garage door opener.
  2. Use a Phillips head screwdriver to remove the side panel on the garage door opener.
  3. Partially insert the battery into the battery compartment with the terminals facing out.
  4. Connect the red (+) and black (-) wires from the garage door opener to the corresponding terminals on the battery.
  5. Replace the battery cover.
  6. Plug in the garage door opener.
  7. Wait for the green Battery Status LED to start flashing before proceeding to test the battery.

Test the Battery

Depending on the power level, the battery may need to charge before performing the test. The garage door opener must be unplugged to test the battery.

  1. Open and close the door using the remote control or door control. While the motor is on, the battery status LED will either glow solid orange, indicating the opener is operating on battery power, or will flash, indicating low battery power. The opener may run slower if the battery is not fully charged.
  2. Plug in the garage door opener. Verify the battery status LED is flashing green, indicating the battery is charging.

Charge the Battery

The battery charges when the garage door opener is plugged into a 120Vac electrical outlet that has power, and requires 24 hours to fully charge. A fully charged battery supplies 12Vdc to the opener for up to 24 hours of normal operation during an electrical power outage. After the electrical power has been restored, the battery will recharge within 24 hours. The battery will last approximately 1 to 2 years with normal usage. Instructions for replacement are provided with the battery. To obtain maximum battery life and prevent damage, disconnect the battery when the opener is unplugged for an extended period of time, such as a summer or winter home.

Battery Status LED

Swipe sideways to see all columns.

Battery status LED (page 9)
LED Meaning
Green (solid) All systems are normal. Battery is fully charged.
Green (flashing) All systems are normal. Battery is being charged.
Orange (solid while motor is on) Opener has lost power and is operating on battery power.
Orange (flashing while motor is on) Battery is low. The opener also beeps every 2 seconds while operating on battery power.
Red (solid) The battery needs to be replaced; it will no longer hold a charge.

LiftMaster says to go to chamberlain.com to purchase a replacement battery. See Maintenance for the yearly battery backup test.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, page 9.

Back to contents

Installation: The Protector System and Door Control

The guide's Installation page (page 10) covers the Protector System (safety reversing sensors) and the door control check. The door will not close unless the sensors are connected and aligned (cover and page 10).

The Protector System (Safety Reversing Sensors)

Be sure power is NOT connected to the garage door opener BEFORE installing the safety reversing sensor. To prevent SERIOUS INJURY or DEATH from a closing garage door: correctly connect and align the safety reversing sensor (this required safety device MUST NOT be disabled), and install the sensor so the beam is NO HIGHER than 6" (15 cm) above the garage floor.

Important: the safety reversing sensors MUST be connected and aligned correctly before the garage door opener will move in the down direction. When the opener has power, check the sensors. If the sensors are aligned and wired correctly, both LEDs will glow steadily: the sending sensor has an amber LED, and the receiving sensor has a green LED (the receiving sensor has a sticker on the back).

To align the safety reversing sensors

  1. Loosen the wing nuts.
  2. Adjust the sensors up or down until both LEDs glow steadily, indicating alignment.
  3. Tighten the wing nut to secure the sensor.

Tip: after tightening the wing nut, lightly wiggle the sensor brackets by hand without blocking the beam to ensure both LEDs remain glowing steady. If the receiving eye flashes while wiggling the brackets, adjust the sensor alignment until a solid LED glow is reached before proceeding.

Safety Sensor Troubleshooting

  • If either sensor LED is off, there is no power to the sensor: check that you have power to the garage door opener; check the sensor wire is not shorted or broken; and check that the sensors are wired correctly (white wires to the white terminal and white/black wires to the grey terminal).
  • If the green receiving sensor LED is blinking, the sensors are obstructed or misaligned: check for obstructions in the sensor light beam; align the sensors; and, if the receiving sensor (green LED) faces direct sunlight, switch the receiving sensor with the sending sensor.

Ensure the Door Control Is Wired Correctly

If the door control has been installed and wired correctly, the command LED on the control panel will glow solid.

Steps Needed to Complete Installation

LiftMaster lists these remaining steps: Introduction (page 11), Program the Travel (page 12), Automatic Force Set Up (page 12), and Test the Safety Reversal System (page 13). They are on this page under Adjustments.

All Security Equipment note. This User's Guide does not include the mechanical installation steps (rail and trolley assembly, header bracket, and mounting the opener). LiftMaster's guide refers to support.chamberlaingroup.com for the complete manual, and says to identify the model number on the end panel of the opener. Use the installation manual for your model for those steps.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, page 10.

Back to contents

Adjustments: Program the Travel and Test Safety Reversal

Introduction

The opener has electronic controls to make setup and adjustments easy. The adjustments allow you to program where the door will stop in the open (UP) and close (DOWN) position. The electronic controls sense the amount of force required to open and close the door, and the force is adjusted automatically when you program the travel (page 11). If anything interferes with the door's upward travel, it will stop. If anything interferes with the door's downward travel, it will reverse.

The programming buttons (UP, DOWN, and the Adjustment button) are located on the left side panel of the opener and are used to program the travel. While programming, the UP and DOWN buttons can be used to move the door as needed.

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. Incorrect adjustment of garage door travel limits will interfere with proper operation of the safety reversal system. After ANY adjustments are made, the safety reversal system MUST be tested. The door MUST reverse on contact with a 1-1/2" (3.8 cm) high object (or a 2x4 laid flat) on the floor. To prevent damage to vehicles, be sure the fully open door provides adequate clearance.

One-piece doors only: when setting the UP travel for a one-piece door, ensure the door does not slant backwards when fully open. If it does, this will cause unnecessary bucking and/or jerking when the door is opening or closing.

Step 1: Program the Travel

While programming the travel, the UP and DOWN buttons can be used to move the door as needed. The safety reversing sensors will be disconnected during the Program the Travel process.

  1. Press and hold the Adjustment button until the UP button begins to flash and/or a beep is heard.
  2. Press and hold the UP button until the door is in the desired UP position.
  3. Once the door is in the desired UP position, press and release the Adjustment button. The garage door opener lights will flash twice, and the DOWN button will begin to flash.
  4. Press and hold the DOWN button until the door is in the desired DOWN position.
  5. Once the door is in the desired DOWN position, press and release the Adjustment button. The garage door opener lights will flash twice. Program the Travel is now complete, and the opener will automatically set the opener's force settings.

Step 2: Automatic Force Set Up

Once both the UP and DOWN positions have been set, the safety reversing sensors reconnect and become operational. The opener then enters a force-sensing operation by automatically moving the door open and close. It sounds an audible and visual alert before automatically opening and closing the door, and beeps three times to confirm that the Automatic Force Set Up completed successfully. Adjustment is then complete.

  • If you hear one long beep after the door attempts to move, the Automatic Force Set Up has not completed successfully. Start over at step 1 of Program the Travel.
  • If the opener lights flash 5 times, programming has timed out and the travel limits have not been set. Restart the Program the Travel process.
  • If the opener lights flash 5 times during the steps for Program the Travel, the programming has timed out. If they flash 10 times, the safety reversing sensors are misaligned or obstructed. When the sensors are aligned and unobstructed, cycle the door through a complete up and down cycle using the remote control or the UP and DOWN buttons; programming is then complete. If you are unable to operate the door up and down, repeat the steps for Program the Travel.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, pages 11 and 12.

Back to contents

Step 3: Test the Safety Reversal System

The safety reversal system MUST be tested every month and after ANY adjustments. The door MUST reverse on contact with a 1-1/2" (3.8 cm) high object (or a 2x4 laid flat) on the floor.

  1. With the door fully open, place a 1-1/2 inch (3.8 cm) board (or a 2x4 laid flat) on the floor, centered under the garage door.
  2. Press the remote control push button to close the door. The door MUST reverse when it makes contact with the board.

If the door stops but does not reverse: (1) repeat Program the Travel by setting the closed limit tighter to the floor (applying slightly more pressure to the door seal may allow the safety reversal system to be set properly), and (2) repeat the safety reversal test. If the test continues to fail, call a trained door technician. It is normal for the trolley to slightly lift the rail with a properly set close limit; ensuring the door is fully closed gives the best opportunity for a successful test.

Step 4: Test the Protector System

  1. Open the door. Place an obstruction in the path of the door.
  2. Press the remote control push button to close the door. The door will not move more than an inch (2.5 cm).

The garage door opener will not close from a remote control if the receiving LED is flashing green, which alerts you that the sensor is misaligned or obstructed.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, pages 12 and 13.

Back to contents

Maintenance and Troubleshooting

Maintenance Schedule

Swipe sideways to see all columns.

LiftMaster Basic Series maintenance schedule (page 14)
How often Task
Every month Manually operate the door. If it is unbalanced or binding, call a trained door systems technician. Check to be sure the door opens and closes fully; adjust if necessary. Test the safety reversal system; adjust if necessary.
Every year Apply garage door lubricant to rollers, bearings, and hinges. (If applicable) test the battery backup and consider replacing the battery so the opener will operate during an electrical power outage (see below).
Every two to three years Use a rag to wipe away existing grease from the opener rail. With another rag, reapply a small layer of white lithium grease and scrub the top and underside rail surface where the trolley slides.

Yearly battery backup test (models with battery backup)

  1. Unplug the garage door opener from AC power. The battery status LED will glow solid orange (opener is operating on battery power) or will flash (low battery power).
  2. Open and close the door using the remote control or door control.
  3. In battery backup mode, the Automatic Garage Door Lock will unlock when the garage door is opened and will remain disabled until power is restored.
  4. Plug in the garage door opener. Verify the battery status LED is flashing green (battery is charging).

The Remote Control Battery

To prevent possible SERIOUS INJURY or DEATH: NEVER allow small children near batteries, and if a battery is swallowed, immediately notify a doctor. To reduce the risk of fire, explosion, or chemical burns, replace ONLY with 3V CR2032 coin batteries, and DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.

LiftMaster's illustration shows how to replace the remote control battery: unscrew the captive screw, pry open the top housing and lift up, remove the old battery out of the holder and replace it with a new battery, then re-attach the top housing and tighten the captive screw.

Troubleshooting

LiftMaster lists these basic troubleshooting tips (page 14). For additional help and support videos, visit LiftMaster.com/CustomerSupport or contact your installing dealer.

Swipe sideways to see all columns.

LiftMaster Basic Series troubleshooting (page 14)
Symptom LiftMaster's guidance
My garage door opener will not close Check that the LEDs in both sensors are glowing steadily. They glow steadily if they are aligned and wired correctly.
My vehicle's HomeLink is not programming to my garage door opener The opener is compatible with HomeLink versions 4, 5 and 6. Contact HomeLink at 1-800-355-3515 or www.HomeLink.com.
My garage door opener beeps The opener senses an obstruction while traveling, or the opener has been activated through a device or feature such as Timer-to-Close, the garage door monitor, or the LiftMaster Internet Gateway.
My neighbor's remote control opens my garage door Erase the memory from your garage door opener and reprogram the remote control(s).
The garage door moves 6-8", stops, or reverses Manually open and close the garage door. The door may be binding or there may be an obstruction; if the door is binding, call a trained door systems technician. Possible travel module failure.
My remote control will not activate the garage door Verify the lock feature is not activated on the door control, or reprogram the remote control.
The wall-mounted door control will not function The wires for the door control are shorted, or the door control is faulty.
Opener hums for 1-2 seconds with no movement and 5 flashes and 5 beeps occur Manually open and close the garage door. The door may be binding or there may be an obstruction; if the door is binding, call a trained door systems technician.
Cannot connect the opener to the home Wi-Fi network Ensure the myQ serial number was entered correctly and try again. The myQ characters are between A-F and 0-9 only.

For the complete manual, LiftMaster directs you to support.chamberlaingroup.com.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, page 14.

Back to contents

Repair Parts

LiftMaster's User's Guide does not list repair parts (page 15). It says: to see repair parts for your garage door opener, identify the model number on the end panel of the opener and visit support.chamberlaingroup.com to download or print the installation manual. The only part number the guide gives is the replacement battery for models with battery backup: LiftMaster part #485LM (page 9). The remote control uses a 3V CR2032 coin battery (page 14).

Shop related items: garage door opener parts | garage door opener accessories | garage door openers

Source: LiftMaster User's Guide 114-6138-000 Rev. C, pages 9, 14 and 15.

Back to contents

Warranty

Per LiftMaster's limited warranty (page 15), LiftMaster ("Seller") warrants to the first retail purchaser of the product, for the residence in which it is originally installed, that it is free from defects in materials and/or workmanship for the periods below, starting from the date of purchase.

Swipe sideways to see all columns.

LiftMaster Basic Series warranty period as printed (page 15)
Model (as printed) Parts Motor Accessories Battery backup Chain
2100L 1 year 5 years 1 year - 1 year
2200L (as printed) 1 year 5 years 1 year - 1 year
2300L 1 year 5 years 1 year 1 year 1 year
2420L 1 year 5 years 1 year 1 year 1 year

Proper operation depends on complying with the instructions for installation, operation, maintenance, and testing; failure to comply strictly will void the limited warranty in its entirety. If the product appears to contain a covered defect during the warranty period, visit LiftMaster.com before dismantling the product. You will be advised of disassembly and shipping. The warranty does not cover non-defect damage, damage from improper installation, operation, or care, labor charges for reinstalling a unit, replacement of consumable items (such as remote control batteries and light bulbs), units installed for non-residential use, any problems with the garage door or its hardware (springs, rollers, alignment, hinges), or problems caused by interference. The complete terms are printed on page 15. LiftMaster's Quebec Right to Repair notice says that availability of spare parts, repair services and information for maintenance or repair is "Not available."

Documentation note. The printed table has a row for "2200L" and none for the 2220L (see the note under The Four Basic Series Models). It also lists "Chain 1 year" for every row, and the product page for the 2220L lists a 5 year motor warranty and 1 year camera, parts, and accessories warranty, while the guide's table has an "Accessories" column but no camera column. Confirm the warranty terms for your model with LiftMaster.

All Security Equipment note. If you bought your opener from All Security Equipment, see our refund policy and our Help Center for how manufacturer warranty returns are handled.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, page 15.

Back to contents

Automatic Garage Door Opener Safety and Maintenance Guide

The last two pages of the User's Guide are a general safety and maintenance guide (pages 17 and 18).

Garage Door Opener Safety: An Automatic Decision

LiftMaster says a garage door is the largest moving object in the home. An improperly adjusted garage door and opener can exert deadly force when the door closes, which could lead to entrapment of children or adults and subsequent injury or death. Proper installation, operation, maintenance, and testing of the door and opener are necessary to provide a safe, trouble-free system. Key points:

  • Garage door openers are not toys. Discuss garage door and opener safety with your children and explain the danger of being trapped under the door. Stay away from a moving door.
  • Keep transmitters and remote controls out of reach of children. Do not let children play with or use transmitters or other remote control devices.
  • The wall-mounted push button should be out of reach of children, at least 5 feet from the nearest standing surface and away from all moving parts. Mount and use the button where you can clearly see the closing garage door.
  • Keep the door in sight until it completely closes when using the wall-mounted push button or transmitter.

Routine Maintenance Can Prevent Tragedies

Make monthly inspection and testing of your garage door and opener system a part of your regular routine. Look for the opener model number on the back of the power unit. Warning: springs are under high tension; only qualified individuals should adjust them.

  • Visually check the door and installation: starting with the door in the closed position, use the manual disconnect on the opener to disconnect the door; look for signs of wear or damage on hinges, rollers, springs, and door panels; contact a trained door systems technician if any damage is evident; and verify the photo eye height is no higher than 6 inches from the garage floor.
  • Test the door for proper operation: open and close the door manually using handles or suitable gripping points. It should move freely and without difficulty, and should balance and stay partially open 3-4 feet above the floor. If you detect any signs of improper operation, contact a trained door systems technician.
  • Test the opener safety features: reconnect the opener to the door using the manual disconnect and open the door. Place a 2x4 board flat in the path of the door and try to close it; the door should stop when it contacts the 2x4 and then reverse direction. Block the photoelectric sensor by waving an object in front of it and attempt to close the door; the door should not close unless the wall-mounted push button is manually held during operation. If the opener does not perform as described, contact a trained door systems technician.

Source: LiftMaster User's Guide 114-6138-000 Rev. C, pages 17 and 18.

Back to contents

Frequently Asked Questions About the LiftMaster Basic Series

What are the Basic Series models, and which ones does All Security Equipment carry?

The Basic Series has four models: the 2100L, 2220L, 2300L, and 2420L. All Security Equipment carries the 2220L and the 2420L. See The Four Basic Series Models.

What is the difference between the 2220L and the 2420L?

Per LiftMaster's guide, both have a camera, and only the 2420L has the battery backup (cover and pages 7 and 9). Our 2220L page also notes that the 2220L does not include a battery backup.

Do I need to program the included remote control?

No. A pre-programmed remote control is included (cover and page 6). To add or reprogram a remote or keypad, see Programming. Older LiftMaster remote controls are not compatible; the opener works only with Security+ 3.0 remotes and wireless keypads.

What Wi-Fi does the opener need?

A 2.4 GHz, 802.11b/g/n signal in the garage, your home network password, and the myQ serial number from the opener (page 5). See myQ App Control and Wi-Fi Setup.

What stops working when the opener is on battery power?

The garage door opener lights, myQ app control and monitoring (and the camera), and unattended close including Timer-to-Close (pages 5, 7, and 9). See Battery Backup.

Why won't my garage door close?

The door will not close unless the Protector System sensors are connected and aligned. Check that the LEDs in both sensors glow steadily (pages 10 and 14). See Safety Sensor Troubleshooting.

How do I set the open and close positions?

Hold the Adjustment button until the UP button flashes, set the UP position, press Adjustment, set the DOWN position, and press Adjustment again; the opener then sets the force automatically (page 12). See Program the Travel. Always test the safety reversal system afterward.

How do I test the safety reversal system?

Place a 1-1/2 inch (3.8 cm) board or a 2x4 laid flat under the fully open door and close the door with the remote; it must reverse on contact. Test it every month and after any adjustment (page 13). See Test the Safety Reversal System.

How do I open the door by hand?

Pull down on the emergency release handle, preferably with the door fully closed. Pulling it down and back engages the lockout feature (page 8). See Open the Door Manually.

What replacement batteries do I need?

The opener's battery backup (2300L and 2420L) uses LiftMaster part #485LM (page 9). The remote control uses a 3V CR2032 coin battery (page 14).

Can I use Timer-to-Close or the myQ app with a one-piece door?

No. LiftMaster says unattended close features, including Timer-to-Close and the myQ app, are to be used ONLY with sectional doors (page 2).

Is the guide available in other languages?

The PDF has the English guide (pages 1 to 18) followed by a French version. This page presents the English version.

Original LiftMaster Documentation

This HTML resource is presented by All Security Equipment, is not a LiftMaster publication, and does not replace the original manufacturer documentation. It is based on LiftMaster's Basic Series garage door opener User's Guide, document 114-6138-000 (Rev. C), ©2026 Chamberlain Group, LLC.

Check LiftMaster's product pages for the current revision before relying on any document, because LiftMaster may update them. LiftMaster directs users to support.chamberlaingroup.com for the complete manual for a model.

Need the opener itself? All Security Equipment sells the LiftMaster Basic Series 2220L (camera) and 2420L (camera and battery backup).

This resource was last updated November 11, 2026. Based on LiftMaster document 114-6138-000 Rev. C.